Fuel Tank Removal (Fig. 12)
Park machine on a level surface, lower cutting
decks, stop engine, engage parking brake and remove
key from the ignition switch.
5. Using labels placed during tank removal, correctly
connect fuel hoses to the fuel supply standpipe, the re-
turn standpipe and the vent elbow fitting. Secure hoses
with hose clamps.
1.
6.
Connect electrical wiring to the fuel sender.
2.
Chock rear wheels and jack up front of machine.
Support machine on jack stands. Remove front, left
wheel to allow fuel tank removal.
A. Connect blue/red wire to the center terminal and
black wire to any of the screws that secure the fuel
sender to the fuel tank.
3.
Use a fuel transfer pump to remove fuel from the fuel
tank and into a suitable container.
B. Apply skin--over grease (Toro Part No. 505--165)
to the wire terminal connections.
4.
Removethree(3)socketheadscrewsthatsecurefit-
ting cover (item 1) to fuel tank. Remove fitting cover.
7. Position fitting cover to fuel tank and secure with
three (3) socket head screws.
5.
Disconnect power (blue/red) and ground (black)
wires from the fuel sender on the fuel tank (Fig. 13).
WARNING
6.
Label fuel hoses to assure proper assembly.Discon-
nect fuel hoses from the fuel supply standpipe (item 3),
the return standpipe (item 4) and the vent elbow fitting
(item 6) in top of tank (Fig. 13).
Failure to maintain proper torque could result in
failure orlossof wheeland mayresult inperson-
al injury.
7.
route fuel lines from standpipes. If necessary, remove
plugs and clamps from top of tank.
Route fuel lines from under clamps (item 13) that
8.
9.
Install front, left wheel assembly.
Lower machine to ground. Torque wheel lug nuts in
8.
that secure tank hold down (item 11) to frame. Remove
tank hold down.
Remove two (2) flange head screws and lock nuts
a crossing pattern from 70 to 90 ft--lb (95 to 122 N--m).
10.Fill fuel tank.
9.
tank.
Slide fuel tank from left side of machine to remove
4
5
10.If
and fuel sender from fuel tank.
necessary, remove standpipes, elbow bushings
1
6
Fuel Tank Installation (Fig. 12)
2
1.
If removed, install standpipes, elbow bushings and
fuel sender into fuel tank.
3
2.
3.
machine frame. Secure hold down with two (2) flange
head screws and lock nuts.
Install fuel tank from left side of machine.
Figure 13
Position tank hold down (item 11) to fuel tank and
1.
2.
3.
Sender power wire
Sender ground wire
Fuel sender
4.
5.
6.
Fuel supply hose
Return fuel hose
Vent hose
4.
Route fuel supply and return hoses under clamps in
top of tank.
Groundsmaster 5900/5910
Page 3 -- 15
Diesel Engine
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 5900, Toro Groundsmaster 5910 |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)