Removal (Fig. 1)
Position machine on a clean, level surface. Lower
cutting decks, stop engine, apply parking brake and re-
move key from the ignition switch.
8. Position damper to mount on cutting deck. Install
spacer and spring pin to secure damper to deck (Figs.
1.
2
and 3).
9. Start engine and lower deck to ground. Stop engine
and remove key from the ignition switch.
2.
Remove center deck cover to access hydraulic deck
motor.
10.Install hydraulic motor to cutting deck (see Cutting
Deck Motor Installation in the Service and Repairs Sec-
tion of Chapter 4 -- Hydraulic Systems).
3.
Remove hydraulic motor from cutting deck (see Cut-
ting Deck Motor Removal in the Service and Repairs
SectionofChapter4 -- HydraulicSystems).Positionand
support motor away from cutting deck.
11.Install all removed cutting deck covers.
12.Lubricate
grease fittings on cutting deck and lift arm
4.
Start engine and raise deck slightly. Stop engine and
assemblies (see Operator’s Manual).
remove key from the ignition switch.
5.
that secure the height--of--cut chains to the rear of the
cutting deck.
Remove hairpins (item 11) and clevis pins (item 12)
8
9
6.
to damper mount on deck (Figs. 2 and 3). Position
damper away from cutting deck.
Remove spring pin and spacer that secure damper
7.
and remove key from the ignition switch.
Start engine and lower deck to ground. Stop engine
8
7
8.
Remove cap screws (item 4), flat washers (item 3),
6
plate(item15)andlocknuts(item14)thatsecureliftarm
support hubs to cutting deck. Remove thrust washer
(item 9) from between the lift arm and the rear, slotted
hole in the support hub.
5
4 3
2
1
9.
Slide the cutting deck away from the traction unit.
Figure 2
Installation (Fig. 1)
Position machine on a clean, level surface. Lower
front lift arms, stop engine, engage parking brake and
remove key from the ignition switch.
1.
2.
3.
4.
5.
Carriage screw (2 used)
Damper mount
Spring pin
6.
7.
8.
9.
Cap screw
Bearing rod end
Flange nut (3 used)
Damper
1.
Spacer
Clevis rod end
2.
3.
that slotted hole in the support hub is toward the rear of
the deck.
Position the cutting deck to the lift arms.
3
Align lift arm support hub to cutting deck. Make sure
1
4.
the rear, slotted hole in the support hub.
Place thrust washer (item 9) between the lift arm and
5.
(item 4), flat washers (item 3), plate (item 15) and lock
Secure lift arm support hub to deck with cap screws
2
nuts (item 14). Torque fasteners from 94 to 116 ft--lb
(128
to 157 N--m).
6.
Start engine and raise deck slightly. Stop engine and
remove key from the ignition switch.
Figure 3
1.
2.
Damper
Clevis rod end
3.
Bearing rod end
7.
height--of--cut chains to the rear of the cutting deck.
Install clevis pins and hairpins that secure the
Groundsmaster 5900/5910
Page 8 -- 7
Cutting Decks
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 5900, Toro Groundsmaster 5910 |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)