Toro 10176SL Service Manual Models 30448 30446 Groundsmaster 4000 4010 D D Preface

Filtering Closed--Loop Traction Circuit
Filtering of a closed--loophydraulic system after amajor
component failure (e.g. traction (piston)  pump or front
wheel motor) is  a requirement to  prevent debris from
transmitting throughout the system. If a closed--loop hy-
draulic system filtering tool is not used to ensure system
cleanliness,repeatfailures,aswellassubsequentdam-
age to other hydraulic components in the affected sys-
tem,  will occur.  To  effectively remove  contamination
from closed--loop traction  circuit, use of the Toro high
flow hydraulic filter and hydraulic hose kits are recom-
mended (see Special Tools in this chapter).
7.  With engine running at low idle speed, slowly move
the traction pedal to the forward direction to allow flow
through thetractioncircuitandhighflowfilter.Keeptrac-
tion circuit engaged for five (5) minutes while gradually
increasing both forward pressure on traction pedal and
engine speed. Monitor filter indicator to make sure that
green color is showing during operation.
8.
With engine running at high idle speed and traction
pedal moved to the forward direction, periodically apply
brakes to  increase pressure  in traction  circuit. While
monitoring filter indicator, continue this  process for an
additional five (5) minutes.
1.
Parkmachineonalevelsurfacewithenginestopped
and key removed from ignition switch.
IMPORTANT: If using a filter that is not the bi--direc-
tional Toro high flow filter, do not press the traction
pedal in  the reverse  direction. If flow  is reversed
when using a filter that is not bi--directional, debris
from the filter will re--enter the traction circuit.
2.
ground (see Jacking Instructions in Chapter 1 -- Safety).
Raise and support machine so all wheels are off the
NOTE:  If front wheel or rear axle motor was replaced,
install high flow filter to the inlet of new motor instead of
tothe traction pump fitting.This willprevent systemcon-
tamination from entering and damaging the new motor.
9.  With engine running at high  idle speed, alternately
movetractionpedalfromforwardtoreverse.Whilemon-
itoring filter indicator, continue this process for an addi-
tional five (5) minutes.
3.
side elbow fitting on bottom of traction pump (Fig. 58).
Disconnect hose from left side pump fitting.
Thoroughly clean junction of hydraulic hose and left
10.Shut engine off and remove key from ignition switch.
4.
Connect Toro high flow hydraulic filter in series be-
11.Remove high flow hydraulic filter and hydraulic hose
kit from machine.  Connect hydraulic hose  to left side
traction pump fitting. Make sure to properly tighten hose
(see Hydraulic Hose and Tube Installation in the Gener-
al Information section of this chapter).
tween traction pump fitting and disconnected hose. Use
hydraulic hose kit (see Special Tools in this chapter) to
connectfiltertomachine.Makesurethatfittingandhose
connections are properly tightened.
IMPORTANT: Use only hydraulic fluids specified in
Operator’sManual.Otherfluidscouldcausesystem
damage.
12.Lower machine to ground.
13.Check
oil level in hydraulic reservoir and add correct
oil if necessary.
5.
fill hydraulic reservoir with new hydraulic oil as required.
After installing high flow filter to machine, check and
6.
draulic leakage from filter and hose connections.  Cor-
rect any leaks before proceeding.
Start engine and run at idle speed. Check for any hy-
RIGHT
FRONT
1
CAUTION
Allwheelswillbeoffthegroundandrotatingdur-
ing this  procedure. Make sure  machine is well
supported so it  will not move  and accidentally
fall to prevent injuring anyone around machine.
IMPORTANT: While  engaging  the traction  circuit,
monitor the indicator on the high flow hydraulic fil-
ter. If the indicator should show red, either reduce
pressure  on the  traction pedal  or reduce  engine
speed to decrease hydraulic flow through the filter.
2
Figure 58
1.
Piston (traction) pump
2.   Left side fitting/hose
Hydraulic System
Page 4 -- 74
Groundsmaster 4000--D/4010--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 340 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website