Toro 10176SL Service Manual Models 30448 30446 Groundsmaster 4000 4010 D D Preface

Hi/Low Speed and Headlight (Groundsmaster 4010--D) Switches
The  Hi/Low speed  and  headlight switches  (Ground-
smaster 4010--D) are identical, two (2) position rocker
switches that are located on the control console.
6.  After  testing is  completed,  connect wire  harness
connector to the switch.
7.
Assemble console arm (see Console Arm Assembly
TheHi/Lowspeedswitch  (Fig.27)isusedasaninputfor
the TEC--5002  controller to  set the  machine traction
speed for Hi speed (2WD) or Low speed (4WD).
in the Service and Repairs section of Chapter 7 -- Chas-
sis).
The Groundsmaster  4010--D headlight  switch  allows
the headlights to be turned on and off.
NOTE:  Before disconnecting the Hi/Low speed switch
for testing,  the switch and  its circuit wiring should  be
tested as a TEC--5002 input with the Diagnostic Display
(see Diagnostic Display in the Troubleshooting section
ofthischapter).IftheDiagnostic   Displayverifies  thatthe
Hi/Low speed switch and circuit wiring are functioning
correctly, no further switch testing is necessary. If, how-
ever,  the Display  determines that  the  Hi/Low speed
switch and circuit wiring  are not functioning correctly,
proceed with test.
2
1
Testing
Figure 27
1.
Make sure ignition switch is OFF. Remove key from
1.
Console arm
2.   Hi/Low speed switch
ignition switch.
2.
thatistobetested(seeConsoleArmDisassembly     inthe
Service and Repairs section of Chapter 7 -- Chassis).
Disassemble console arm to gain access to switch
3.
Disconnect harness  electrical  connector from  the
switch.
4.
With  the use  of a  multimeter  (ohms setting),  the
BACK OF SWITCH
switch functions  may be tested to  determine whether
continuity exists between the various terminals for each
switch position.  The switch  terminals are  marked as
shown in Figure 28. The circuitry of the switch is shown
in the chart below. Verify continuity between switch ter-
minals.  Replace  switch  if  testing  identifies  a  faulty
switch.
Figure 28
NOTE:  Switch terminals 1, 4, 5 and 6 are not used on
Groundsmaster 4000--D and 4010--D machines.
SWITCH
POSITION
CIRCUIT 1
2 + 3
CIRCUIT 2
5 + 6
ON
OFF
2 + 1
5 + 4
5.
If switch tests correctly and circuit  problem still ex-
ists, check wire harness (see Electrical Schematics and
Wire Harness Drawings in Chapter 10 -- Foldout Draw-
ings).
Electrical System
Page 5 -- 26
Groundsmaster 4000--D/4010--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 340 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website