Toro 10176SL Service Manual Models 30448 30446 Groundsmaster 4000 4010 D D Preface

General Information
Operator’s Manual
The Operator’s Manual provides information regarding
the operation, general maintenance  and maintenance
intervals for yourGroundsmaster machine. Refer tothat
publication for additional information when servicing the
machine.
Toro Electronic Controllers (TEC)
Groundsmaster 4000--Dand4010--Dmachinesusetwo
The controllers appear identical but they are different in
termsoftheconnectorsandinternalhardware.Theyare
arranged in ”master / slave” configuration and therefore
cannotbeinterchanged.TheTEC--5002mastercontrol-
ler is responsible for powering up the TEC--5001 slave
controller. The TEC--5002 also controls the engine start
circuit.
(2)
Toro Electronic  Controllers (TEC) to  manage ma-
chine electrical functions. The controllers are micropro-
cessor controlled  that sense  the condition of  various
switches (inputs) and direct electrical power to control
appropriate machine functions (outputs) based  on the
inputs. Communication between  the two Toro control-
lers is provided with a CAN--bus system. The status of
inputs to the controllers as well as outputs from the con-
trollers can  be monitored with the  Diagnostic Display
(see Special Tools in this chapter).
IMPORTANT: Before performing any welding on the
machine, disconnect  the  battery cables  from the
battery,  disconnect  the  wire  harness  connector
fromboth of the TEC controllers and disconnect the
terminal connector from the alternator. These steps
will prevent damage to the machine electrical sys-
tem.
CAN--bus Communications
The
TEC--5002) used on  the Groundsmaster 4000--D and
4010--D
system. Using thissystem allows the traction unit tofully
integrate all the  different electrical components of the
machine andbring themtogether asone. TheCAN--bus
system reduces the  number of electrical  components
and connections used on  the machine and allows the
number of wires in the wire harness to be significantly
reduced.
two
(2)
TEC
controllers
(TEC--5001
and
CAN identifies the Controller Area Network that is used
between the controllers on the Groundsmaster. Two (2)
specially designed, twisted cables form the bus. These
wires provide the data pathways  between the control-
lers (TEC--5001 and TEC--5002) used on the machine.
The engineering termfor these two (2) cables are CAN--
high and CAN--low. At the ends of the twisted pair of bus
cables are 120 ohm termination resistors.
communicate with each other  on a CAN--bus
Each of the components that is controlled by the CAN--
buslinkonlyneedsfour(4)wirestooperateandcommu-
nicate to the system: CAN--high, CAN--low, B+ (power)
and ground.
Electrical Drawings
The electrical schematic and wire harness drawings for
Groundsmaster 4000--D and 4010--D machines are lo-
cated in Chapter 10 -- Foldout Drawings.
Electrical System
Page 5 -- 2
Groundsmaster 4000--D/4010--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 340 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website