Toro 10176SL Service Manual Models 30448 30446 Groundsmaster 4000 4010 D D Preface

7.
Torque nut from 90 to 100 ft--lb (123 to 135 N--m) while
Installballjointmounttoballjointwithslottedhexnut.
CAUTION
aligning cotter pin holes. Install cotter pin.
8.
Installation in Chapter 8 -- Cutting Decks).
Install front  cutting  deck (see  Front Cutting  Deck
When changing attachments,  tires or perform-
ing other  service, use  correct jacks  and  sup-
ports. Make sure machine is parked on a solid,
level surface such as a  concrete floor. Prior to
raising machine, remove any  attachments that
may interfere with the safe and proper raising of
themachine.Alwayschockorblockwheels.Use
jack stands to support the raised machine. If the
machine  is  not   properly  supported  by  jack
stands, the  machine may  move  or fall,  which
may result in personal injury.
9.
jam nut from 150 to 175 ft--lb (203 to 237 N--m).
Ifballjointwasremoved   fromliftarm,torqueballjoint
10.Lubricate
lift arm grease fittings.
11.
tingdecktoverifythathydraulichosesandfittingsdonot
contact anything.
Afterassemblyiscompleted,raiseandlowerthecut-
12.Check
height--of--cut and deck pitch adjustment.
3.
Chock rear  wheels and  jack up  front of machine.
Support machine on jack stands.
4.
moved.
Remove front wheel next to lift arm that is to be re-
1
5.
cure liftcylinder pin to liftarm. Remove pin and separate
lift cylinder and lift arm.
Remove cap screw, washers  and lock nut that se-
6.
Remove lock nut that secures lift arm pin. Support lift
2
arm and slide pin from frame  and lift arm. Remove lift
arm from frame.
0.870”
(22.1
mm)
7.
ball joint from removed lift arm as required.
Remove height--of--cut  chain, ball joint mount  and
Installation (Fig. 2)
Figure 3
1.
U--bolt
2.
Height--of--cut chain
1.
Position lift arm to frame and insert lift arm pin. En-
gage roll pin into frame slots and install lock nut on pin.
Torque lock nut from 60 to 70 ft--lb (81 to 94 N--m).
2.
arm and cylinder end. Secure pin with cap screw, wash-
ers and lock nut.
Align lift cylinder with  lift arm. Slide pin through  lift
1
3.
the ground. Make sure that wheel lug nuts are torqued
Install front wheel assembly  and lower machine to
from 85 to 100 ft--lb (115 to 135 N--m).
4.
secure plate fully forward in lift arm slot.
If sensing plate (item 32) was removed from lift arm,
2
5.
If height--of--cut chain u--bolt was removed from lift
arm, assemble u--bolt so that threaded portion extends
0.870”
3).
(22.1 mm) above mounting plate on lift arm (Fig.
2.210”
to 2.390”
(56.1
to 60.7 mm)
6.
If removed, install ball joint to lift arm. Distance from
endofliftarmtocenter   ofballjointshouldbefrom2.210”
to 2.390” (56.1 to 60.7 mm) (Fig. 4). Make sure that ball
joint is horizontal and that stud is centered in ball joint.
Install deck before torquing ball joint jam nut (item 24).
Figure 4
1.
Lift arm
2.
Ball joint
Groundsmaster 4000--D/4010--D
Page 7 -- 5
Chassis
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 340 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website