Toro 10176SL Service Manual Models 30448 30446 Groundsmaster 4000 4010 D D Preface

Cutting Deck Lift Switches
The cutting deck lift switches are used as inputs for the
TEC--5001 controller to raise or lower the cutting decks.
When the front of a lift switch is depressed and held, the
controlled decks will lower. When the rear of a lift switch
is depressed and held, the controlled  decks will raise.
The decks will remain in position when the switch is re-
leased. The lift switches are located on the console arm
(Fig. 25).
7.  After  testing is  completed,  connect wire  harness
connector to the lift switch.
8.
Assemble console arm (see Console Arm Assembly
in the Service and Repairs section of Chapter 7 -- Chas-
sis).
3
NOTE:  To lower the cutting decks, traction speed has
to be in  low range (4WD).  Also, to raise or  lower the
decks, the operator seat has to be occupied.
2
Testing
1.
Before disconnecting the  lift switch for testing,  the
switch  and  its  circuit wiring  should  be  tested  as  a
TEC--5001 input with the Diagnostic Display (see Diag-
nostic Display  in  the Troubleshooting  section of  this
chapter). If the  Diagnostic Display verifies that  the lift
switch andcircuit wiring arefunctioning correctly,nofur-
ther switch testing is necessary. If, however, the Display
determines that the lift switch and circuit wiring are not
functioning correctly, proceed with test.
4
1
Figure 25
1.
2.
Console arm
Front deck lift switch
3.
4.
RH deck lift switch
LH deck lift switch
2.
Make sure ignition switch is OFF. Remove key from
ignition switch.
3.
deck lift switches (see Console Arm Disassembly in the
Service and Repairs section of Chapter 7 -- Chassis).
Disassemble console arm to gain access to cutting
4.
Disconnect harness electrical connector from the lift
switch that is to be tested.
BACK OF SWITCH
5.
26.
The switch terminals are marked as shown in Figure
The circuit logic of the lift switches is shown in the
Figure 26
chartbelow.Withtheuseofamultimeter     (ohmssetting),
theswitchfunctionsmaybetestedtodeterminewhether
continuity exists between the various terminals for each
position.Verifycontinuity  betweenswitch terminals.Re-
place lift switch if testing identifies a faulty switch.
NOTE:  Lift switch terminals 4, 5 and 6 are not used on
Groundsmaster 4000--D and 4010--D machines.
SWITCH
POSITION
CLOSED
CIRCUITS
OPEN
CIRCUITS
DECK LOWER
2 + 3
2 + 1
5 + 4
5
+ 6
NEUTRAL
NONE
2 + 1
ALL
DECK RAISE
2 + 3
5 + 6
5
+ 4
6.
Ifliftswitch  tests correctly and circuitproblem stillex-
ists, check wire harness (see Electrical Schematics and
Wire Harness Drawings in Chapter 10 -- Foldout Draw-
ings).
Groundsmaster 4000--D/4010--D
Page 5 -- 25
Electrical System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 340 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website