Toro 10176SL Service Manual Models 30448 30446 Groundsmaster 4000 4010 D D Preface

Disassembly (Figs. 115 and 116)
Removeoilfromliftcylinderintoadrainpanbyslowly
pumping the cylinder shaft. Plug  both ports and clean
the outside of the cylinder.
Assembly (Figs. 115 and 116)
1.
1.  Make sure all cylinder components are clean before
assembly.
2.
Coat new seal kit components with clean hydraulic
IMPORTANT: Prevent  damage when clamping  the
cylinder in a vise; clamp on the clevis only.
oil.
A.  Install new seals and O--rings to the piston.
2.
the clevis end of the barrel. Use of a vise with soft jaws
is recommended.
Mount lift cylinder securely in a vise by clamping on
B.  Install new seals, O--ring and back--up ring to the
head.
IMPORTANT: Do  not clamp  vise jaws  against the
shaft surface.
3.
Loosen head from barrel:
A.  Use a spanner wrench to rotate head clockwise
until the edge ofthe retaining ring appears in the bar-
rel opening.
3.
Mountshaftsecurelyinavisebyclampingonthecle-
vis of the shaft.
A.  Coat shaft with clean hydraulic oil.
B.  Insert a screwdriver under the  beveled edge of
the retaining ring to start the  retaining ring through
the opening.
B.  Carefully slide head  and piston onto  the shaft.
Secure piston to shaft with lock nut.
C. Rotatetheheadcounter--clockwisetoremovere-
taining ring from barrel and head.
C. Torque  lock  nut to  specification  in Figure  115
(side deck cylinder) or Figure 116 (front deck cylin-
der).
4.
Extract shaft with head and piston by carefully twist-
ing and pulling on the shaft.
4.
Lubricate head and piston  with clean hydraulic oil.
Carefully slide shaft assembly into cylinder barrel.
IMPORTANT: Do  not clamp  vise jaws  against the
shaft surface.
IMPORTANT: Prevent  damage when clamping  the
cylinder’s barrel  into a  vise; clamp  on the  clevis
only.
5.
Mountshaftsecurelyinavisebyclampingonthecle-
vis of the shaft.  Remove lock nut and piston  from the
shaft. Slide head off the shaft.
5.
Mount lift cylinder  in a vise  with soft jaws. Secure
head in barrel:
6.
Remove and discard all seals and O--rings from the
piston and the head.
A.  Align retaining ring hole in the head with the ac-
cess slot in the barrel.
7.
Wash parts  in clean  solvent. Dry  parts with  com-
pressed air. Do not wipe parts dry with paper towels or
cloth. Lint in a hydraulic system will cause damage.
B.  Insert the retaining ring hook into the hole and ro-
tate head clockwise until  the retaining ring is com-
pletely pulled into the  barrel and the ring ends are
covered.
8.
Carefully inspect internal surface of barrel for dam-
age(deepscratches,out--of--round,etc.).Inspectpiston
rod and piston for evidence of excessive scoring, pitting
or wear. Replace lift cylinder if internal components are
found to be worn or damaged.
C. Apply silicone sealer to barrel access slot.
Groundsmaster 4000--D/4010--D
Page 4 -- 149
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 340 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website