Toro 10176SL Service Manual Models 30448 30446 Groundsmaster 4000 4010 D D Preface

Removal (Fig. 114)
Park  machine  on  a  level  surface,  lower  cutting
decks, stop  engine, apply parking  brake and remove
key from the ignition switch.
Installation (Fig. 114)
1.
1.  If fittings were  removed from lift  cylinder, lubricate
and place new O--rings onto fittings. Install fittings into
port openings  using marks  made during the  removal
process  to properly  orientate fittings.  Tighten fittings
(see Hydraulic Fitting Installation in  the General Infor-
mation section of this chapter).
2.
Installing Hydraulic System Components at the begin-
ning of the Service and Repairs section of this chapter.
Read the  General Precautions  for Removing  and
2.
ot pin into frame and clevis. Secure pivot pin with cotter
pin.
Positioncylinder barrelclevistoframeandinsertpiv-
3.
lift cylinder removal, thoroughly clean exterior of cylin-
der and fittings.
To prevent contamination of hydraulic system during
3.
shaft clevis. Secure pin toliftarm with cap screw, two (2)
flat washers and lock nut.
Insert pin  assembly  through lift  arm and  cylinder
WARNING
4.
Hose and Tube Installation in the General Information
section of this chapter).
Attach hydraulic hoses to lift cylinder (see Hydraulic
Make sure that front cutting deck is fully lowered
before loosening hydraulic lines from front deck
lift cylinders. If deck is  not fully lowered as hy-
draulic lines are loosened, deck may drop unex-
pectedly.
5.  Fill reservoir with hydraulic fluid as required.
6.
After assembly is completed, operate lift cylinder to
verify that hydraulic hoses and fittings are not contacted
by anything.
NOTE:  To ease installation, tag the hydraulic hoses to
show their correct position on the lift cylinder.
4.
5.
that secure the pin assembly to the lift arm. Remove pin
assembly from lift arm and  cylinder shaft clevis which
will free lift cylinder from lift arm.
Disconnect hydraulic hoses from lift cylinder.
Remove lock nut, two (2) flat washers and cap screw
6.
upper end of lift cylinder to machine. Pull pivot pin from
frame and cylinder barrel clevis.
Remove one cotter pin  from pivot pin that secures
7.
8.
er,markfittingorientation  toallowcorrect  assembly.Re-
move fittings from cylinder and discard O--rings.
Remove lift cylinder from machine.
If hydraulic fittings are to be removed from lift cylind-
Groundsmaster 4000--D/4010--D
Page 4 -- 147
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 340 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website