Toro 10176SL Service Manual Models 30448 30446 Groundsmaster 4000 4010 D D Preface

Verify Diagnostic Display Output Functions
B.  If the output LED’s are on  as specified, but the
machine does not function properly, suspect a failed
electrical component, an open in the tested circuit or
a non-electrical problem (e.g. hydraulic component
problem). Repair as necessary.
The Diagnostic  Display also  has the  ability to detect
which output solenoids or relays are  energized by the
TECcontrollers.Thisisaquickwaytodetermineifama-
chine malfunction is electrical or hydraulic.
C. If each input switch is in the correct position and
functioning correctly,  but the output LED’s  are not
correctly illuminated, this indicates a TEC controller
problem. If this occurs, contact your Toro Distributor
for assistance.
NOTE:  Anopenoutput(e.g.anunpluggedconnectoror
a broken wire) cannot be detected with the Diagnostic
Display.
1.
Park machine on a level  surface, lower the cutting
decks, stop the engine and engage the parking brake.
7.
After output  functions testing is  complete, discon-
nect the Diagnostic Display connector from the harness
connector and plug loopback  connector into wire har-
ness. Secure controller cover to frame.
2.
harness loopback connector (Fig. 11). Locate wire har-
ness communication port and loopback connector (Fig.
Remove the controller cover to allow access to wire
12).
connector.
Carefully unplug loopback connector from harness
2
1
3
3.
ConnecttheDiagnosticDisplayconnectortothehar-
nessconnector.Makesurecorrectoverlaydecalisposi-
tioned on the Diagnostic Display (Figs. 9 and 10).
4
4.
Turn the ignition switch to the ON position.
5
NOTE:  The red text on the Diagnostic Display overlay
decal refers to input switches and the green text refers
to TEC outputs.
5.
Make sure that the “OUTPUTS DISPLAYED” LED,
on lower right column ofthe Diagnostic Display,isillumi-
nated.  If “INPUTS  DISPLAYED”  LED  is illuminated,
press the  toggle button  on the Diagnostic  Display to
change the LED to “OUTPUTS DISPLAYED”.
RIGHT
FRONT
6
Figure 11
NOTE:  It may  be necessary  to  toggle between  “IN-
PUTS DISPLAYED” and “OUTPUTS DISPLAYED” sev-
eral times to perform the following step. To change from
inputs to outputs, press toggle button once. This may be
done as  often  as required.  Do not  press and  hold
toggle button.
1.
2.
3.
Controller cover
Screw (2 used)
4.
5.
6.
U--nut (2 used)
TEC--5001
TEC--5002
Flat washer (2 used)
1
2
6.
Sit on seat and attempt to operate the desired func-
tion  of  the  machine. The  appropriate  output  LED’s
should illuminate on the Diagnostic Display to indicate
that the TEC controller is turning on that function. The
GLOWPLUGS,HIRANGEandOKRUNoutputscanbe
checked with the ignition switch in the ON position and
the engine not running. For testing of the hydraulic sole-
noid outputs (e.g. ENABLE, C DECK RAISE, R DECK
FLOAT), the engine must be running.
A.  IfthecorrectoutputLED’sdonotilluminate,verify
that the required input switches are in the necessary
positions to allow that function to occur.
3
Figure 12
1.
2.
Wire harness connector
Loopback connector
3.
Diagnostic display
Electrical System
Page 5 -- 10
Groundsmaster 4000--D/4010--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 340 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website