Toro 10176SL Service Manual Models 30448 30446 Groundsmaster 4000 4010 D D Preface

Cutting Deck Position Switches
Three (3) cutting deck position switches are used on the
Groundsmaster 4000--D and 4010--D. These switches
are located on the traction unit frame (Figs. 59 and 60).
The position switches are powered proximity switches
that incorporate an internal reed switch and a LED. The
deck  position  switches  are  used  as  inputs  for  the
TEC--5001 controller to prevent deck operation when a
cutting deck is raised. The switch sensing plates are at-
tached  to  the  cutting  deck   lift  arms.  The  position
switches for front and side decks are different.
The single front cutting deck position switch is a normal-
ly closed switch. When the front cutting deck is lowered,
thesensing plateontheliftarmisawayfromtheposition
switch sotheswitch is inits normally closed state.When
the front  cutting  deck is  raised, the  sensing plate  is
moved near the position switch and the switch opens.
2
1
3
The two (2) side cutting deck position switches are nor-
mally open switches. When a side cutting deck is low-
ered,the sensing plate onthe liftarm isnear theposition
switch and the switch closes. When a side cutting deck
israised,thesensingplateismovedawayfromtheposi-
tion switch so the switch is in its normally open state.
Figure 59
1.
2.
Front lift arm (lowered)
Position switch
3.
Sensing plate
Testing
1.
The cutting deck position switches and  their circuit
wiring should be tested as a TEC--5001 input  with the
Diagnostic Display (see Diagnostic Display in the Trou-
bleshooting section  of this chapter).  If the Diagnostic
Displayverifiesthatthepositionswitchesandcircuitwir-
ing are functioning correctly, no further switch testing is
necessary. If, however,  the Display determines that  a
positionswitchandcircuitwiringarenotfunctioningcor-
rectly, proceed with test.
2.
decks, stop engine and apply parking brake.
Park  machine  on  a  level  surface,  lower  cutting
3.
Turn ignition switch to the ON position (do not start
engine)  and  check  LED  on   cable  end  of  position
switches (Fig. 61). Switch LED  should be illuminated
when the cutting decks are fully lowered.
2
4
3
1
4.
Start engine, fully raise cutting decks and then stop
engine. Then, turn ignition switch to the ON position (do
notstartengine)andcheckLEDoncableendofposition
switches. Switch LED should not be illuminated when
the cutting decks are fully raised.
Figure 60
1.
2.
Side lift arm (LH shown)
Position switch
3.
4.
Sensing plate
Clearance
5.
If a position switch LED did not function correctly:
A.  Position cutting deck so sensing plate on the lift
arm is  near the position  switch (front cutting deck
raised and side cutting decks lowered).
Electrical System
Page 5 -- 44
Groundsmaster 4000--D/4010--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 340 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website