Toro 10176SL Service Manual Models 30448 30446 Groundsmaster 4000 4010 D D Preface

Removal (Fig. 9)
Park machine on a level surface, lower cutting deck,
CAUTION
1.
stop engine,  engage parking  brake  and remove  key
from the ignition switch.
Be careful when installing  the idler spring. The
spring is under heavy load and may cause  per-
sonal injury.
2.
Remove deck covers from top of cutting deck.
CAUTION
3.  Use spring hook tool to attach the idler spring (item
15)
onto the adjusting screw (item 4) and shoulder bolt
on idler arm.
Be  careful  when  removing  idler   spring.  The
spring is under heavy load and may cause  per-
sonal injury.
4.  With the idler arm tensioning the drive belt, the idler
spring hook  to hook length  should be  from 3.250” to
3.750”
(82.6 to 95.2 mm) (Fig. 10). If necessary, discon-
nect spring  and  change position  of  adjusting screw.
When idler spring is the correct length, tighten second
flange nut to secure idler adjustment.
3.
15)
Use spring hook tool to unhook the idler spring (item
from the adjusting screw (item 4).
4.
Remove drive belt(s) from deck pulleys.
5.
Adjust location of idler stop bolt so that the clearance
5.
bolt(item 10)to cutting deck toallow clearance between
idler arm and stop bolt.
Loosen flange nuts (item 11) that  secure idler stop
between idlerarm andidler stopboltheadis  from0.125”
to 0.185” (3.2 to 4.6 mm) (Fig. 10).
6.
7.
Lubricate idler arm grease fitting.
Install deck covers to cutting deck.
6.
Remove idler components as needed using Figure
9
as a guide. Note location of washers, idler spacer and
screw as idler assemblies are being removed.
1
Installation (Fig. 9)
2
3
1.
Install removed idler components using Figure 9 as
a guide.
A.  Make sure that one (1) thrust washer (item 19) is
placed above and below  the idler arm. Location of
additional washer (item 22) depends on whether the
idlerpulleymountsonthebottomsideoftheidlerarm
or on the top of the idler arm.
B.  Secure idler arm assembly to  cutting deck with
retaining ring.
0.125”
to 0.185”
3.250”
to 3.750”
C. Ifidlerstopbolt(item10)wasremovedfromdeck,
makesurethatitisinstalledintheholethatallowsthe
stop bolt head to align with the idler arm.
(3.2 to 4.6 mm)
(82.6
to 95.2 mm)
Figure 10
1.   Idler stop bolt
2.   Idler spring
3.   Adjusting screw
2.
Install drive belt to pulleys.
Groundsmaster 4000--D/4010--D
Page 8 -- 11
Cutting Decks
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 340 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website