Toro 10176SL Service Manual Models 30448 30446 Groundsmaster 4000 4010 D D Preface

Removal (Fig. 72)
Park  machine  on  a  level  surface,  lower  cutting
decks, stop  engine, apply parking  brake and remove
key from the ignition switch.
Installation (Fig. 72)
1.
IMPORTANT: If  90o fitting  (item 10)  was removed
from backplate of RH wheel motor, make sure that
straight fittings (item 14) are installed and correctly
torqued before installing 90o fitting.
2.
Read the  General Precautions  for Removing  and
Installing Hydraulic System Components at the begin-
ning of the Service and Repairs section of this chapter.
1.  If fittings  were removed from  motor, lubricate  and
place new O--rings onto fittings. Install fittings into port
openingsusingmarksmadeduringtheremovalprocess
to properly  orientate fittings. Tighten  fittings (see Hy-
draulic  Fitting Installation  in the  General Information
section of this chapter).
NOTE:  Toeaseinstallation,labelthehydraulichosesto
show their correct position on the wheel motor.
3.
Disconnect hydraulic hoses  and tubes from wheel
motor. Put caps or plugs on motor ports and hose open-
ings to prevent contamination.
2.
motortobrakeassembly  makingsurethatarrows   onthe
side of motor case point upward.
Install O--ring  (item 8)  onto motor. Position  wheel
IMPORTANT: Before  loosening fasteners, support
wheel motor to prevent motor fromfalling during re-
moval.
3.
Slide motor into brake assembly.
Align splines on motor shaft and splined brake shaft.
4.
Remove wheel motor using Figure 72 as a guide.
4.
Secure motor  to brake assembly  with cap screws
andflatwashers.Tightencapscrews   from75to85ft--lb
to 115 N--m).
5.
mark fitting orientation  to allow correct assembly. Re-
move fittings from motor and discard O--rings.
If hydraulic  fittings are to be  removed from motor,
(101
5.
Remove plugs  from  wheel motor  ports and  hose
openings. Using  labels placed during  motor removal,
correctly attach hydraulic hoses and tubes to wheel mo-
tor (see  Hydraulic Hose  and Tube  Installation in  the
General Information section of this chapter).
6.
7.
Fill reservoir with hydraulic fluid as required.
Properly fill hydraulic system (see Charge Hydraulic
System in this section).
Groundsmaster 4000--D/4010--D
Page 4 -- 93
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 340 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website