Toro 10176SL Service Manual Models 30448 30446 Groundsmaster 4000 4010 D D Preface

Input Shaft/Pinion Gear
35
to 41 ft--lb
(
47 to 56 N--m)
1
18
2
3
20
19
17
4
5
6
7
8
16
18
9
10
15
14
10
9
13
11
35 to 41 ft--lb
(47 to 56 N--m)
12
Figure 32
1.
2.
3.
4.
5.
6.
7.
Nut (2 used)
Lock washer (2 used)
Stud (2 used)
Lock nut
Stake washer
Oil seal
O-ring
8.
9.
Seal collar
15. Gear case
16. Gasket
17. Cover plate
18. Dowel pin
19. Lock washer (6 used)
20. Cap screw (6 used)
Bearing
10. O-ring
11. Input shaft/pinion gear
12. Bearing case
13. Shim
14. Screw (2 used)
The following procedures assume the rear axle assem-
bly has been removed from the machine.
NOTE:  Replacement input shaft/pinion gear (item 11)
is only  available in  matched set  with differential  ring
gear.
Removal (Fig. 32)
Installation (Fig. 32)
1.
Remove the cover plate, gasket and gear case as-
sembly from the axle assembly.Remove thegasketand
any remaining gasket material.
NOTE:  When installing bearing  cones onto the  input
shaft/pinion gear,  press only on  the inner race of  the
bearing cone.
2.
Remove the retaining rings and the driven gear from
the input shaft/pinion gear.
1.  If the inner bearing cone was removed, press a new
bearingconeallthewayontotheinputshaft/piniongear.
3.
Remove input shaft/pinion gear assembly from  the
gear case.  Remove  the shims  and bearing  case O-
rings.
2.  Place the shaft and bearing assembly in the bearing
case and install the outer bearing cone.
4.
Remove and discard the stake washer.
Release the stake washer and remove the lock nut.
NOTE:  The  bearings  must   be  completely   seated.
There should be no input shaft/pinion gear end play.
5.
bearing cone and bearing  case. Remove and discard
the oil seal and O-ring.
Drive the input shaft/pinion gear out from the outer
3.  Coat a new oil seal with grease and install as shown
(Fig. 33). The  seal should be installed with  the garter
spring towards the hydraulic motor location.
6.
cases for damage and  wear. Replace components as
necessary.
Inspect  all  gears,  shafts, bearings,  spacers  and
4.  Coat new O-ring with grease. Install O-ring in the oil
seal collar and install the collar.
Axles, Planetaries and Brakes
Page 6 -- 28
Groundsmaster 4000--D/4010--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 340 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website