Toro 10176SL Service Manual Models 30448 30446 Groundsmaster 4000 4010 D D Preface

Fuses
The fuse blocks are located in the power center under
the hood on the right side of the machine (Fig. 17).
Fuse Testing
Turn ignition switch to the ON position (do not start en-
gine). With the  fuse installed in  the fuse block, use  a
multimeter to verify that 12 VDC exists at both of the ter-
minal test points on the fuse. If 12 VDC exists at one of
the fuse test points but not at the other, the fuse is faulty.
In addition to the fuses in the fuse blocks, a 40 amp fuse
(F5--1) is included in the wire harness to protect the pull
coil circuit for the engine run solenoid. This fuse resides
in a fuse holder near the starter motor (Fig. 17).
Fuse Identification and Function
If necessary, make sure that ignition switch is OFF and
key is  removed from  switch. Remove fuse  from fuse
block and check that fuse has continuity across the fuse
terminals.
UseFigure18toidentifyeachindividualfuseanditscor-
rect amperage in the fuse block. The fuses have the fol-
lowing functions.
Fuse F1--1 (20 amp) protects engine starter circuit.
2
Fuse F1--3 (10 amp)  protects light circuit on Ground-
smaster 4010--D.
Fuse  F1--4 (10  amp) protects  signal  light circuit  on
Groundsmaster 4010--D.
Fuse F2--2 (10 amp) protects operator seat circuit.
Fuse F2--3 (10 amp) protects power point circuit.
FuseF2--4(10amp)protectsmainpowersupplycircuit.
1
Fuse F3--1 (2 amp) protects logic  power circuit to the
TEC--5002 controller.
Figure 17
Fuse F3--2  (7.5 amp)  protects power  supply for  the
1.
Power center
2.
Fuse F5--1
TEC--5002 controller outputs.
Fuse F3--3  (7.5 amp)  protects power  supply for  the
TEC--5002 controller outputs.
M1 (60A)
M2 (60A)
Fuse F3--4  (7.5 amp)  protects power  supply for  the
TEC--5002 controller outputs.
F1
FRONT
Fuse F4--1 (2 amp) protects logic  power circuit to the
TEC--5001 controller.
F2
F3
Fuse F4--2  (7.5 amp)  protects power  supply for  the
TEC--5001 controller outputs.
Fuse F4--3  (7.5 amp)  protects power  supply for  the
TEC--5001 controller outputs.
Fuse F4--4  (7.5 amp)  protects power  supply for  the
TEC--5001 controller outputs.
F4
Fuse M1 (60A) protects engine glow plug circuit.
1
2
3
4
Fuse M2 (60A) protects operator cab circuit on Ground-
smaster 4010--D.
Figure 18
Groundsmaster 4000--D/4010--D
Page 5 -- 21
Electrical System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 340 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website