Toro 10176SL Service Manual Models 30448 30446 Groundsmaster 4000 4010 D D Preface

Component Testing
For accurate resistance and/or continuity checks, elec-
trically disconnect the component being tested from the
circuit (e.g. unplug the ignition switch connector before
checking continuity on the switch).
CAUTION
When testing electrical components for continu-
ity with a multimeter (ohms setting), make sure
that power to the circuit has been disconnected.
NOTE:  For engine component testing information, see
Engine,
Series at the end ofChapter 3 -- Kubota Die-
the
03--M--E3B
sel Engine.
Kubota
Workshop
Manual,
Diesel
Ignition Switch
The ignition (key) switch on the console arm has three
6.  If ignition switch tests correctly  and circuit problem
still exists, check wire harness (see Electrical Schemat-
ics and Wire Harness Drawings in Chapter 10 -- Foldout
Drawings).
(3)
positions (OFF,  ON/PREHEAT and  START)  (Fig.
15).
Testing
7.
connector to the ignition switch.
After testing is completed, connect the wire harness
1.
Before disconnecting the ignition switch for testing,
the switch and  its circuit wiring should be  tested as a
TEC--5002 input with the Diagnostic Display (see Diag-
nostic Display  in  the Troubleshooting  section of  this
chapter). If the Diagnostic Display verifies that the igni-
tionswitchandcircuitwiringarefunctioningcorrectly,no
further switch testing is necessary. If, however, the Dis-
playdeterminesthattheignitionswitchandcircuitwiring
are not functioning correctly, proceed with test.
8.
in the Service and Repairs section of Chapter 7 -- Chas-
sis).
Assemble console arm (see Console Arm Assembly
2
2.
Make sure ignition switch is OFF. Remove key from
ignition switch.
3.
switch (see Console  Arm Disassembly in  the Service
and Repairs section of Chapter 7 -- Chassis).
Disassemble console arm to gain access to ignition
4.
Disconnect wire harness  electrical connector from
the ignition switch.
5.
The ignition switch terminals are identified as shown
1
in Figure 16.  The circuit logic of  the ignition switch  is
shown in the chart below. With the use of a multimeter
(ohms setting), the switch functions can be tested to de-
termine whether continuity exists between the various
terminals for each switch position. Verify continuity be-
tweenswitchterminals.Replaceignitionswitchiftesting
identifies that switch is faulty.
Figure 15
1.
Console arm
2.
Ignition switch
ON/PREHEAT
45
o
45o
OFF
START
POSITION
OFF
CIRCUIT
NONE
A
F
ON/PREHEAT
START
B + C + F,  D + E
A + B + C
B
C
E
D
FRONT VIEW
REAR VIEW
Figure 16
Electrical System
Page 5 -- 20
Groundsmaster 4000--D/4010--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 340 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website