Toro 10176SL Service Manual Models 30448 30446 Groundsmaster 4000 4010 D D Preface

PTO Switch
The PTO switch is located on the console arm (Fig. 23).
The PTO switch  is pulled up to  engage the PTO and
pushed in to disengage the PTO.
6.  If PTO switch tests correctly and circuit problem still
exists, check wire harness (see  Electrical Schematics
and Wire Harness  Drawings in Chapter  10 -- Foldout
Drawings).
The TEC--5001 controller  monitors the position of the
PTO switch (up  or down). Using inputs from  the PTO
switch and other switches  in the interlock system, the
TEC--5001 controller controls the energizing of the hy-
draulic solenoid valves  used to drive the cutting  deck
motors.
7.  After testing is completed, connect the wire harness
connector to the PTO switch.
8.
Assemble console arm (see Console Arm Assembly
in the Service and Repairs section of Chapter 7 -- Chas-
sis).
NOTE:  To engage the PTO, the seat has  to be occu-
pied, traction speed has to be in Low range (4WD) and
the cutting decks have to be fully lowered.
1
Testing
1.
Before disconnecting the PTO switch for testing, the
switch and its circuit wiring should be tested as a TEC
input with the Diagnostic Display  (see Diagnostic Dis-
playintheTroubleshootingsectionofthischapter).Ifthe
Diagnostic Display verifies that the PTO switch and cir-
cuit wiring  are functioning correctly, no  further switch
testingisnecessary.If,however,theDisplaydetermines
that the PTO switch and circuit wiring are not function-
ing correctly, proceed with test.
2
2.
ignition switch.
Make sure ignition switch is OFF. Remove key from
Figure 23
2.   Control console
1.
PTO switch
3.
switch (see Console  Arm Disassembly in  the Service
and Repairs section of Chapter 7 -- Chassis).
Disassemble console  arm to  gain access  to PTO
4
1
4.
Disconnect harness  electrical  connector from  the
PTO switch.
5
2
5.
24.
The switch terminals are marked as shown in Figure
The circuit logic of the PTO switch is shown in the
chartbelow.Withtheuseofamultimeter     (ohmssetting),
the switch functions can be tested to determine whether
continuity exists between the various terminals for each
switch position. Verify continuity between switch termi-
nals. Replace PTO switch if testing identifies that switch
is faulty.
3
6
Figure 24
1.
2.
3.
COM B terminal
NO B terminal
NC B terminal
4.
5.
6.
COM C terminal
NO C terminal
NC C terminal
SWITCH
POSITION
CLOSED
CIRCUITS
OPEN
CIRCUITS
NOTE:  Only PTO switch terminals COM C and NO C
are used on Groundsmaster 4000--D and 4010--D ma-
chines.
OFF (DOWN)
COM B + NC B    COM B + NO B
COM C + NC C   COM C + NO C
ON (UP)
COM B + NO B    COM B + NC B
COM C + NO C   COM C + NC C
Electrical System
Page 5 -- 24
Groundsmaster 4000--D/4010--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 340 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website