7.
Install fan motor and fan assembly (Fig. 15).
13.Connect wires and/or electrical connections to the
following electrical components:
A. Carefullypositionfanmotor,fanandmotorbrack-
et assembly to radiator.
A. The temperature sender and alternator (Fig 11).
B. The glow plug (Fig. 12).
B. Secure fan motor bracket to radiator with six (6)
cap screws and flange nuts.
C. The engine run solenoid.
C. Remove caps and plugs placed in hoses and fit-
tings during removal to prevent contamination.
D. Battery,frameandwireharnessgroundtotheen-
gine block.
D. Connect hydraulic hoses to cooling fan motor
(see Hydraulic Hose and Tube Installation in the
GeneralInformationsectionofChapter4 -- Hydraulic
System).
E. The starter and low oil pressure switch (near
starter).
F. The air conditioning compressor (Groundsmas-
ter 4010--D machines).
8.
Position upper radiator shroud and coolant reservoir
withbrackettotheradiator.Secureshroudandreservoir
bracket to the radiator and lower radiator bracket with
removed fasteners (seeRadiator Installation in thissec-
tion). Make sure thatclearance between shroud and fan
is at least 0.180” (4.6 mm) at all points.
14.Install
aircleanerassembly totheengine(seeAirFil-
ter System Installation in this section).
15.Install
exhaustsystemtomachine(seeExhaustSys-
tem Installation in this section).
9.
14):
Connect throttle cable to injector pump (Figs. 13 and
16.Connect
diator drain is shut. Fill radiator and reservoir with cool-
ant.
coolant hoses to the radiator.Make sure ra-
A. Secure throttle cable swivel to speed control le-
ver with lock nut.
17.Check
position of wires, fuel lines, hydraulic hoses
and cables for proper clearance with rotating, high tem-
perature and moving components.
B. Place throttle cable under cable clamp.
C. Adjust throttle cable position in cable clamp so
that engine governor lever contacts the high speed
stop bolt at the same time that the throttle lever con-
tacts the end of the slot in the control console.
18.Install
battery to machine (see Battery Service in the
Service and Repairs section of Chapter 5 -- Electrical
System). Make sure to connect positive battery cable
first and then negative battery cable. Secure battery to
machine with strap and cover.
D. Tighten cable clamp to secure throttle cable.
19.Check and adjust engine oil as needed.
20.Check and adjust hydraulic oil as needed.
21.Bleed fuel system.
10.Connect
fuel line to the injection pump (Fig. 13).
11.
Install transport cylinder assembly to engineadapter
plate (Fig. 16). Make sure that cylinder spacer is posi-
tioned between transport cylinder and engine mount.
22.Start
engine and operate hydraulic controls to prop-
12.On
Groundsmaster 4010--D machines:
erly fill hydraulic system (see Charge Hydraulic System
in the Service and Repairs section of Chapter 4 -- Hy-
draulic System).
A. Position windshield washer reservoir to bracket
on engine (Fig. 17). Secure with removed fasteners.
23.Close
and secure hood.
B. Install air conditioning compressor to brackets
(see Air Conditioning Compressor Installation in the
Service and Repairs section of Chapter 9 -- Operator
Cab).Makesurethatdrivebeltisproperlytensioned.
C. Connect coolant hose to fitting on engine water
flange.
Kubota Diesel Engine
Page 3 -- 16
Groundsmaster 4000--D/4010--D
Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
---|---|
Tags | Toro Groundsmaster 10176SL, Toro Groundsmaster 30446, Toro Groundsmaster 30448, Toro Groundsmaster 4010 D |
Download File |
|
Document Type | Catalog |
Language | English |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)