Toro 10176SL Service Manual Models 30448 30446 Groundsmaster 4000 4010 D D Preface

Removal (Figs. 11 and 12)
Park  machine  on  a  level  surface,  lower  cutting
decks, stop  engine, apply parking  brake and remove
key from the ignition switch.
4.  Install drive belt to  spindle pulleys and idler pulley.
Adjustdrivebelttension(seeIdlerAssembly    Installation
in this section).
1.
5.  If drive spindle was removed, install hydraulic motor
to cutting deck (see Cutting Deck  Motor Installation in
the Service and Repairs Section of Chapter 4 -- Hydrau-
lic Systems).
2.
Remove covers from cutting deck to allow access to
blade spindle.
3.
motor from cutting  deck (see Cutting Deck Motor  Re-
moval in the Service and Repairs Section of Chapter 4
--
spindle.
If drive spindle is to  be serviced, remove hydraulic
IMPORTANT: Pneumatic grease guns can produce
air pockets when filling large cavities and therefore,
are not recommended to be used for proper greas-
ing of spindle housings.
Hydraulic  Systems).   Position  motor   away  from
6.
spindle housing and fill housing cavity with grease until
grease starts to come out of lower seal.
Attach a hand pump grease gun to grease fitting on
4.
(see Idler Assembly Removal in this section). Remove
drive belt from spindle to be serviced.
Loosen idler assembly to release drive belt tension
7.
Install covers to cutting deck.
5.
Start the engine and raise the cutting deck. Stop en-
gine and remove key from the ignition switch. Latch or
block up the cutting deck so it cannot fall accidentally.
6
3
6.
Remove cutting blade, anti--scalp cup and blade bolt
4
from spindle to be serviced.
7.
Remove spindle housing assembly from deck.
1
A.  For driven spindle assemblies, remove eight (8)
flange  head screws  with  flange nuts  that  secure
spindle to deck.
2
B.  Fordrivespindleassemblies,removefour(4)cap
screws with  washers that  secure spindle  and hy-
draulic motor mount to deck. Remove motor mount.
Then, remove four (4) flange head screws with flan-
ge nuts that secure spindle to deck.
7
8
5
C. Lift spindle assembly from deck.
10
11
9
88
(120
to 108 ft--lb
to 146 N--m)
Installation (Figs. 11 and 12)
Position spindle on cutting deck noting orientation of
1.
grease fitting(Fig.11).Securespindleassembly   todeck
with removed fasteners.
Figure 12
1.
Deck (RH shown)
Driven spindle
Drive spindle
Flange head screw
Flange nut
7.
8.
9.
10. Anti--scalp cup
11. Blade bolt
Washer
Cap screw
Blade
2.
Install cutting blade, anti--scalp cup and blade bolt to
spindle. Tighten blade bolt from 88 to 108 ft--lb (120 to
N--m).
2.
3.
4.
5.
6.
146
Drive belt
3.
Slowly rotate cutting blades to verify that blades do
not contact any deck components.
Groundsmaster 4000--D/4010--D
Page 8 -- 13
Cutting Decks
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 340 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website