5.
install.Adjustsetscrew untilitbottoms outoninputshaft
then back out one-quarter turn.
ApplyLoctite#242orequivalenttosetscrew (18)and
6.
Install wiper seal (10) on input shaft.
7.
Install new O-ring (2) onto plug (1) and install plug.
Adjust plug until there is no play in the valve spool with
input shaft held stationary. Install set screw (24) and
tighten to 17 to 25 in-lbs. (2 to 3 Nm).
Neutral Lockout Switch Disassembly
1.
Loosen set screw (17) and remove neutral lockout
switch (15) from adapter (12).
2.
RemoveNeutrallockoutadapter (12)fromcontrolas-
sembly.
3.
Remove pin (14), ball (13), and O-rings (16) from
adapter (12).
Neutral Lockout Switch Assembly
1.
Install new O-rings (11 & 16) onto adapter and pin
(14).
2.
with petroleum jelly to hold in place during installation.
Install ball (13) and pin (14) into adapter. Lubricate
3.
Install adapter (12) into control assembly and tighten
to 44 to 53 ft-lbs. (60 to 70 Nm).
4.
lockout switch (15) and install into adapter (12). Adjust
neutral lockout switch as follows:
Apply Loctite #222 or equivalent to threads of neutral
Figure 34
5.
entposition,thelightshouldbeon.Movethecontrolarm
out of detent, the light should go off.
Test the switch by moving the control arm to the det-
A. Install switch, while moving control arm back and
forth, until “detent” action is detected. Back out the
switch until the “detent” action is very slight.
6.
Removetestlightandputservocontrol assembly into
operation.
B. Obtain a test light or use a multimeter. Attach the
leads from the test light to the switch or the wiring
connector.
C. Move the control arm out of the detent position.
The test light will go on. Screw in the switch until the
light goes off. Mark this as position “A” (Fig. 34).
Move the control arm to the detent position and the
test light should come back on.
D. Leaving the control arm in the detent position, the
light will remain on. Screw in the switch until the light
goes off. Mark this position “B” (Fig. 34).
E. Unscrew the switch one third of the distance be-
tween “B” and “A”. Install and tighten the hex socket
head set screw in one of the upper quadrants of the
hexoftheswitch adapter (Fig. 34).Tightensetscrew
to 28 to 34 in-lbs. (3.2 to 3.8 Nm).
Reelmaster 6500-D/6700-D
Page 4 - 59
Hydraulic System
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro Reelmaster 6500-D, Toro Reelmaster 6700-D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Product Type | Walk Behind Mower |
| Engine Manufacturer | Toro |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)