B. Remove flange head screw (item 11) that retains
drive pulley. Pull drive pulley from drive shaft. Locate
and retrieve square key (item 4) from drive shaft.
B. Press bearings into groomer plate so that bear-
ings contact shoulder in groomer plate bore.
C. Install grease seals so that seal lips are posi-
tioned toward the groomer blade location. Seals
should be flush with surface of groomer plate.
NOTE: To prevent groomer shaft from turning when
removing driven pulley, use wrench on shaft flats to
hold groomer shaft.
D. Press bushings into groomer plate until the bush-
ing contacts the shoulder in the groomer plate bore.
C. Remove the flange nut (item 6) that secures driv-
en pulley (item 5) to groomer shaft. Slide driven
pulley from shaft.
E. If groomer studs (not shown) were removed from
groomer plate (item 17), install new studs into
groomer plate and torque from 14 to 18 ft--lb (19 to
24 N--m).
D. Slide washer (item 3) and pulley spacer (item 2)
from groomer shaft.
E. Remove shoulder bolt that secures quick--up ball
joint rod to groomer plate (Fig. 10).
2
1
F. Disconnect extension spring (item 14) from stud
on groomer plate.
G. Remove two (2) socket head screws (item 7) that
secure groomer components to cutting unit side
plate.
H. Remove pivot hub and idler plate assembly from
cutting unit.
3
I. Support groomer shaft to prevent it from falling.
Carefully slide drive side groomer plate from groom-
er shaft and cutting unit. Remove groomer shim.
4
3
4
4
3.
non--drive side of cutting unit:
To remove groomer plate assembly from groomer
Figure 5
1.
2.
Drive side groomer plate
Non--drive groomer plate
3.
4.
Bearing
Grease seal
A. Remove hydraulic reel motor from cutting unit
(see Hydraulic Reel Motor Removal in the Service
and Repairs section of Chapter 7.2 -- DPA Cutting
Units).
B. Remove two (2) socket head screws (item 7) that
secure groomer components to cutting unit side
plate.
17
(23
to 21 ft--lb
to 28 N--m)
C. Remove pivot hub from cutting unit.
D. Support groomer shaft to prevent it from falling.
Carefully slide non--drive side groomer plate from
groomer shaft and cutting unit.
3
2
4.
Inspect seals, bearings and bushing in groomer
plates. Remove and discard damaged or worn compo-
nents.
Installation (Fig. 4)
1
1.
If seals, bearings or bushing was removed from
groomer plates, install new components noting proper
orientation as shown in Figure 5.
Figure 6
3.
1.
2.
Groomer plate
Shoulder bolt
Quick--up ball joint rod
A. Pack bearings with grease before installation.
Reelmaster 6500--D/6700--D
Page 7.3 -- 7 Rev. E
DPA Groomer
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro Reelmaster 6500-D, Toro Reelmaster 6700-D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Product Type | Walk Behind Mower |
| Engine Manufacturer | Toro |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)