Reel Assembly Removal (Fig. 25)
Position machine on a clean and level surface, lower
1.
cutting units, stop engine, engage parking brake and re-
move key from the ignition switch.
2.
Remove the cutting unit from the machine and place
on a flat work area.
8
3.
If cutting unit is equipped with acounterweight on LH
side plate (as shown in Figure 25), remove the two (2)
capscrewssecuringthecounterweighttothesideplate.
Remove counter weight from the cutting unit. Remove
and discard o--ring from counter weight.
1
2
4.
Ifcutting unitis equipped with anoptional groomer or
9
rear roller brush, remove components for those options
from left hand side plate of cutting unit. See Service and
Repairs section of Chapter 8 -- Groomer for information
on groomer. See Rear Roller Brush in the Service and
Repairs section of this chapter for information on rear
roller brush.
4
5
6
3
4
Loctite #242
27
to 33 ft--lb
7
(
37 to 44 N--m)
15 to 19 ft--lb
to 25 N--m)
(20
5.
Remove the bedbar pivot bolt and washers from the
LH side plate.
Figure 26
1.
Carrier frame
Shim (if equipped)
Support tube
Frame spacer
Flat washer
6.
7.
8.
9.
Cap screw
6.
LHsideplate(seeFrontRollerRemovalandRearRoller
Removal in this section).
Loosen fasteners that secure front and rear rollers to
2.
3.
4.
5.
Flange head screw
Rear grass shield
LH side plate
7.
grass shield to LH side plate (Fig. 26).
Remove cap screw and flat washer that secure rear
Reel Assembly Installation (Fig. 25)
Thoroughly clean side plates and other cutting unit
components. Inspect side plates for wear or damage
and replace if needed.
1.
8.
tube, frame spacer and carrier frame to LH side plate
(Fig. 26).
Remove flange head screw that secures support
Note:
Check that grease seals on cutting reel shaft
Note:
on the cutting reel shaft and should remain on the reel
when removing the LH side plate.
The reel bearings andgrease seals are press fit
are flush to 0.060” (1.5 mm) away from retaining ring on
reel shaft. If necessary, adjust position of grease seals
to allow proper clearance.
9.
24)
Removeshoulderbolts(item8)andflangenuts(item
that secure the LH side plate to the cutting unit
2.
Make sure that grease seals and bearings are prop-
erly greased and positioned on cutting reel (see Reel
Assembly Service in this section). Apply thin coat of
grease to outside of grease seals and bearings on cut-
ting reel to ease reel installation. Also, apply grease to
bearing bores and threads in side plates.
frame.RemovetheLHsideplatefromthereelshaft,roll-
ers, bedbar and cutting unit frame.
CAUTION
CAUTION
Contact with the reel, bedknife or other cutting
unit parts can result in personal injury. Use
heavy gloves when removing the cutting reel.
Contact with the reel, bedknife or other cutting
unit parts can result in personal injury. Use
heavy gloves when installing the cutting reel.
10.Carefully
slide the cutting reel with bearings, grease
seals and splined inserts from the RH side plate.
11.
quired (see Reel Assembly Service in this section).
Inspect and service cutting reel assembly as re-
IMPORTANT: During cutting reel installation, keep
inner and outer bearing races aligned. If bearing
races are not aligned, binding will occur and reel
installation may cause bearing damage.
Reelmaster 6500--D/6700--D
Page 7.2 -- 23 Rev. E
DPA Cutting Units
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro Reelmaster 6500-D, Toro Reelmaster 6700-D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Product Type | Walk Behind Mower |
| Engine Manufacturer | Toro |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)