3.
From the roller tube end with only the inner seal
IMPORTANT: When roller assembly is installed to
cutting deck, make sure that grease groove in each
roller mount aligns with the grease hole in each end
of roller shaft.
installed, carefully install the roller shaft into the roller
tube. Make sure that seals are not damaged as shaft is
installed.
4.
of roller tube:
Install new bearing and outer seals into second end
NOTE: After roller is installed to cutting deck, lubricate
roller grease fittings, rotate roller to properly distribute
grease in bearings and clean excess grease from roller
ends. A properly assembled roller should rotate with
less than 5 in--lbs (0.68 N--m) resistance.
A. Position a second new bearing to roller shaft and
tube.Position washer(seeSpecialTools)onbearing
to allow pressing on both inner and outer bearing
races simultaneously.
1
3
4
2
5
B. Use washer and bearing/outer seal tool (see
Special Tools) with a soft face hammer to fully seat
bearing (Fig. 37). After bearing installation, make
sure that shaft freely rotates and that no binding is
detected. If necessary, lightly tap bearing and/or
shaft ends to align shaft and bearings. Remove
washer from roller.
C. Apply a small amount of grease around the lip of
both outer seals.
Figure 36
D. Carefully install first outer seal into roller tube
making sure that seal lip (and garter spring) faces
end of tube. Use bearing/outer seal tool (see Special
Tools) and soft face hammer to lightly seat seal (Fig.
1.
2.
3.
Roller tube
Inner seal
Bearing
4.
5.
Outer seal
Bearing/outer seal tool
38).
Make sure that shaft and bearings still freely ro-
1
2
3
4
5
tate after seal installation.
6
E. Using the same process, install second outer
sealmakingsuretonotcrushtheinstalledouterseal.
Again, make sure that shaft and bearings still freely
rotate.
IMPORTANT: Make sure that all grease is removed
from shaft threads to prevent bearing lock nut loos-
ening.
Figure 37
5.
Thoroughly clean threads on both ends of roller
shaft.
1.
2.
3.
Roller tube
Roller shaft
Inner seal
4.
5.
6.
Bearing
Washer
Bearing/outer seal tool
NOTE: If original bearing lock nut(s) are being used,
apply Loctite #242 (or equivalent) to threads of lock
nut(s).
1
2
3
4
5
6
6.
Install bearing lock nut onto each end of the roller
shaft. Make sure that outer seals are not damaged dur-
ing nut installation. Torque lock nuts from 50 to 60 ft--lb
(68
to 81 N--m).
7.
If set screw was removed from either end of roller
shaft, apply Loctite #242 (or equivalent) tothreads ofre-
moved set screw and install into roller shaft. Tighten set
screw until it bottoms in shaft and is recessed in shaft.
Figure 38
1.
2.
3.
Roller tube
Roller shaft
Inner seal
4.
5.
6.
Bearing
Outer seal
Bearing/outer seal tool
Reelmaster 6500--D/6700--D
Page 7.2 -- 35 Rev. E
DPA Cutting Units
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro Reelmaster 6500-D, Toro Reelmaster 6700-D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Product Type | Walk Behind Mower |
| Engine Manufacturer | Toro |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)