Rear Roller
Removal (Fig. 30)
4
1
1.
Position machine on a clean and level surface, lower
cutting units, stop engine, engage parking brake and re-
move key from the ignition switch.
2.
on a level working surface. Place support blocks under
bedbar to raise rear roller from work surface.
Remove the cutting unit from the machine and place
5
3.
Loosen two (2) flange nuts that secure the rear roller
shaft to each rear roller bracket.
6
4. On one of the rear roller brackets:
On cutting units equipped with optional High
2
Note:
Height of Cut Kit, there will be additional roller shims
installed between rear roller bracket and cutting unit
side plate.
3
Figure 30
A. Remove flange nuts and carriage screws that se-
cure rear roller bracket and roller shims to the cutting
unit side plate.
1.
2.
3.
Rear roller assembly
Rear roller bracket
Carriage screw
4.
5.
6.
Flange nut
Roller shim
0.010” shim (if needed)
3.
Slide rear roller shaft into the rear roller bracket at-
B. Remove the roller bracket and roller shims from
the rear roller and cutting unit.
tached to the cutting unit. Slide second rear roller brack-
etontotheother end ofroller shaft.Secure second roller
bracket and shims to cutting unit side plate with two (2)
carriage screws and flange nuts. Do not fully tighten
flange nuts.
5.
Slide the rear roller assembly from the remaining
rear roller bracket on the cutting unit.
6.
and roller shims from the cutting unit.
If necessary, remove the second rear roller bracket
4.
place by tightening four (4) flange nuts.
Center rear roller to the cutting reel and secure in
Installation (Fig. 30)
5.
6.
Lubricate rear roller.
1.
Place cutting unit on a level working surface.
Refer to Cutting Unit Operator’s Manual for
Adjust cutting unit (see Cutting Unit Operator’s
Manual).
Note:
number of roller shims required for various height of cut
settings.
Note:
A 0.010” shim (part number 107--4001) is avail-
able to allow for leveling of the rear roller (see Leveling
Rear Roller in the Set--up and Adjustments section of
this chapter). If necessary, this shim would be used on
one side of the rear roller and should be installed be-
tween the rear roller bracket and roller shim.
2.
Ifbothrearrollerbracketswereremovedfromcutting
unit side plate, position brackets and roller shims to one
of the side plates. Install two (2) carriage screws and
flangenutstoretainbracketinposition.Donotfullytight-
en flange nuts.
Reelmaster 6500--D/6700--D
Page 7.2 -- 31 Rev. E
DPA Cutting Units
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro Reelmaster 6500-D, Toro Reelmaster 6700-D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Product Type | Walk Behind Mower |
| Engine Manufacturer | Toro |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)