Backlapping
DANGER
2
2
TO AVOID PERSONAL INJURY OR DEATH:
Never place hands or feet in the reel area
while the engine is running.
When backlapping, run engine at idle speed
D
D
only.
D
then restart.
1
1
While backlapping, the reels may stall and
D
Do not attempt to restart reels by hand or
foot.
D
running.
Do not adjust reels while the engine is
D
attempting to clear the reel.
If a reel stalls, stop engine before
Figure 16
1. Reel Speed Selector Knobs
Backlap Levers
D
one motor causes rotation in other motors.
Reelmotorsareconnectedinseries:rotating
2.
Note:
Additional instructions and procedures on
backlapping are available in the Toro Service Training
Book,Sharpening ReelandRotary Mowers (partno.
80300SL)
.
Note:
Whenbacklapping,thefrontunitsalloperateto-
gether, and the rear units operate together.
1
1.
Position the machine on a level surface, lower the
cutting units, stop the engine, move the Enable/Disable
switch to disable position, and engage the parking
brake.
Figure 17
2.
3.
levers (or knobs) (Fig. 16). Rotate the desired backlap
lever(s) to the backlap position and the desired reel
speed selector knob(s) to position “1.”
Unlock and raise the seat to expose controls.
1. Long Handle Brush
Locate the reel speed selector knobs and backlap
7. Apply lapping compound with a long handle brush
(see Special Tools) (Fig. 17). Never use a short handled
brush.
Note:
Backlapping speed may be increased by mov-
DANGER
ing the reel speed selector knob toward “13.” Each posi-
tion will increase speed approximately 100 rpm. After
changingselector,wait30secondsforthesystemtosta-
bilize at the new speed.
Reels may stall while backlapping. Do not
attempt to restart reels by hand or touch reels
while backlapping. Stop engine and turn reel
speed adjustment knob one position toward
”13.”
4.
for backlapping on all cutting units which are to be back-
lapped.
Make initial reel to bedknife adjustments appropriate
8.
If reels stall or become erratic while backlapping,
5.
Start engine and run at idle speed.
stop backlapping by moving the Lower Mow/Lift control
lever rearward. Once the reels have stopped, move the
desired reel speed selector knob(s) one position closer
to“13.”ResumebacklappingbymovingtheLowerMow/
Lift control lever forward.
6.
Move Lower Mow/Lift control forward to start backlap-
ping operation on designated reels.
Move Enable/Disable switch to Enable position.
DPA Cutting Units
Page 7.2 -- 16 Rev. E
Reelmaster 6500--D/6700--D
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro Reelmaster 6500-D, Toro Reelmaster 6700-D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Product Type | Walk Behind Mower |
| Engine Manufacturer | Toro |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)