Cutting Unit Installation
Cutting unit models 03860, 03861, and 03862 can be
installed at any of the mounting locations on the traction
unit.Figure1showstheorientationofthehydraulicdrive
motor for each of the five locations. For any of the loca-
tions requiring the motor to be mounted on the right end
of the cutting unit, install a counter weight on the left end
of the cutting unit. For the locations requiring the motor
to be mounted on theleftend,install acounter weighton
the right end of the cutting unit.
Motor
Weight
Weight
Motor
Weight
Motor
#4
#1
#5
Motor
Weight
Weight
Motor
#2
#3
Motor
Weight
Weight
Motor
Note:
Counterweight
mounting
capscrews
are
#6
#7
shipped installed on the right bearing housing of thecut-
ting units. The capscrews on left bearing housing are to
be used for securing the hydraulic motor.
Figure 38
1.
just per Cutting Unit Operator’s Manual.
Removecuttingunitsfromcartons.Assembleandad-
2.
Remove protective plugs from each end of cutting
unit.
3.
ing groove on each end of cutting unit (Fig. 39 & 41).
Lubricate and install a large O-ring into bearing hous-
2
Note:
Lubricate internal splines of cutting unit reels
shafts with grease before installing cutting unit motors.
4.
cutting unit with capscrews provided (Fig. 39).
Install a counter weight onto appropriate end of each
1
3
5.
Thoroughly grease the cutting unit reel bearings prior
to installation on the traction unit. Grease should be evi-
dent at the inboard reel seals (see Lubrication in this
section of this manual).
Figure 39
1. Bearing Housing
3. Counterweight
2.
O-ring
6.
knuckle as shown (Fig. 40).
Insert a thrust washer onto horizontal shaft of pivot
5
7.
Insert the horizontal shaft of the pivot knuckle into the
mounting tube of the carrier frame.
8.
washer, flat washer and a flange head capscrew.
Secure pivot knuckle to carrier frame with a thrust
9.
knuckle.
Insert a thrust washer onto vertical shaft of pivot
3
2
10.
Insert the vertical shaft of the pivot knuckle into lift
arm pivot hub (Fig. 40). Guide the pivot knuckle in place
between the two rubber centering bumpers in the under
side of the lift arm steering plate.
1
11.
Insert the lynch pin into the cross hole on the pivot
4
knuckle shaft (Fig. 40).
Figure 40
1.
2.
3.
Carrier Frame
4. Lynch Pin
5. Steering Pin
Pivot Knuckle
Lift Arm Steering Plate
Reelmaster 6500-D/6700-D
Page 7 - 25
Cutting Units
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro Reelmaster 6500-D, Toro Reelmaster 6700-D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Product Type | Walk Behind Mower |
| Engine Manufacturer | Toro |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)