8.
(Fig. 48):
Install rotary handle (reel manifold shown in Fig. 46)
B. Remove lower retaining ring from mow/backlap
spool. Raise mow/backlap spool to allow access to
retaining ring on upper end of spool. Remove upper
retaining ring.
A. Placehandlebaseonflowcontrolvalve andposi-
tion alignment mark on base with number 1 on man-
ifold. Secure base with two (2) set screws. Apply a
light coating of grease to chamfer on top of base to
ease seal installation.
C. Push spool down until o--ring and back--up ring
are exposed on bottom of mow manifold. Remove
lower o--ring and back--up ring from spool.
B. Make sure that sleeve bearing is in handle cap. If
necessary, press sleeve bearing into cap. Install lip
seal on cap with seal lip facing down.
D. Pull spool up and out of mow manifold. Remove
o--rings and back--up ring from spool.
E. Discard removed o--rings and back--up rings.
Visually inspect the spool and manifold port for dam-
age to the sealing surfaces, damaged threads and con-
tamination.
C. Place bushing onto cartridge valve stem. Use a
small amount of grease to keep bushing toward the
top of the valve stem.
2.
D. Place compression spring and detent pin into
handle cap. Use a small amount of grease to hold
detent pin in place.
3.
Install spool into mow manifold (Fig. 46):
A. Installo--ringsandback--upringtouppergrooves
on spool. Apply a light coating of grease to o--rings.
E. Make sure that flow control valve is closed by ro-
tating valve stem fully clockwise. During handle
installation, DO NOT rotate valve stem or speed ad-
justment will be incorrect.
B. Carefully push spool down into mow manifold
portuntillowero--ringandback--upringgroove isex-
posedonbottomofmanifold.Installlowero--ringand
back--upring tospool. Apply alightcoating ofgrease
to o--ring.
F. Press handle cap onto valve stem with arrow on
cappointingtonumber9onmanifold.Makesurethat
detent pin and spring stay positioned in cap.
C. Carefully raise mow/backlap spool until upper re-
taining ring groove on spool is exposed on top of
manifold. Install upper retaining ring.
G. While pressing on the cap to keep the lip seal in
place, rotate cap in a clockwise direction until the ar-
row on the cap aligns with number 1 on the manifold.
By rotating the cap clockwise, the valve will remain
closed. Install screw to retain cap.
D. Push mow/backlap spool down and install lower
retaining ring to spool.
E. If handle was removed from spool, position spool
so handle location of spool is between stop pins. Ap-
ply Loctite 603 Retaining Compound (or equivalent)
to threads on handle and install handle into spool.
H. Make sure that alignment marks oncap andbase
areinlineandthatarrowoncapispointingtonumber
1
on manifold. Tighten two (2) set screws to secure
handle cap.
F. Place ball and dowel pin in backlap switch man-
ifold port. Install new o--ring onto backlap switch.
Thread backlap switch into port and torque 15 ft--lb
Mow/Backlap Spools (Reel Manifold Shown in Fig.
46)
(20
N--m).
1.
Remove spool from mow manifold (Fig. 46):
A. Remove backlap switch from mow manifold be-
fore removing mow/backlap spool. Remove dowel
pin and ball from manifold port after switch is re-
moved. Remove and discard o--ring from switch.
Reelmaster 6500-D/6700-D
Page 4 - 79 Rev. E
Hydraulic System
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro Reelmaster 6500-D, Toro Reelmaster 6700-D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Product Type | Walk Behind Mower |
| Engine Manufacturer | Toro |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)