2.
drive side of cutting unit:
Install groomer plate assembly to groomer non--
I. Check pulley alignment by laying a straight edge
along the outer face of the drive pulley (Fig. 7). Drive
and driven pulleys should be in line within 0.030”
A. Carefully position non--drive side groomer plate
onto groomer shaft and slide to cutting unit.
(0.76
mm). If necessary, align pulleys by removing
driven pulley from groomer shaft and installing or re-
moving washer(s) (item 3) between driven pulley
and pulley spacer.
B. Position pivot hub to cutting unit.
C. Secure groomer components to cutting unit side
plate with two (2) socket head screws (item 7).
J. After pulleys are aligned, install groomer drive
belt and groomer belt cover (see Groomer Belt Re-
placement in this section).
D. Installhydraulic reelmotor tocuttingunit(seeHy-
draulic Reel Motor Installation intheService andRe-
pairs section of Chapter 7.2 -- DPA Cutting Units).
4.
Check that excluder seals just touch groomer plate
assembly. Reposition excluder seals on groomer shaft
if necessary.
3.
Install groomer plate assembly togroomer driveside
of cutting unit:
5.
Checkgroomerreelheightandmowerheight--of--cut
settings. Adjust as needed.
A. Position groomer shim to cutting unit side plate.
Carefully position drive side groomer plate onto
groomer shaft and slide to cutting unit.
6.
Lubricate groomer bearings.
NOTE: After greasing groomer bearings, operate
groomer for 30 seconds, stop machine and wipe excess
grease from groomer shaft and seals.
B. Positionpivothubandidlerplateassemblytocut-
ting unit side plate and secure with two (2) socket
head screws (item 7).
C. Connect extension spring (item 14) to stud on
groomer plate. Make sure that spring is in the stud
groove and that spring hook is positioned toward the
drive pulley.
D. Secure quick--up ball joint rod to drive side
groomer plate with shoulder bolt (Fig. 6). Torque
shoulder bolt from 17 to 21 ft--lb (23 to 28 N--m).
1
E. Slide pulley spacer (item 2) and washer (item 3)
onto groomer shaft.
F. Apply antiseize lubricant to square key (item 4)
that locates drive pulley to pivot hub shaft. Position
key into shaft slot.
3
2
NOTE: To prevent cutting reel from turning when
installing drive pulley, block cutting reel with piece of
wood.
Figure 7
1.
2.
Drive pulley
Driven pulley
3.
Straight edge
G. Apply Loctite #242 to threads of flange head
screw that secures drive pulley to pivot hub shaft.
Slide drive pulley onto shaft and secure with flange
head screw. Torque screw from 27 to 32 ft--lb (37 to
43
N--m).
NOTE: To prevent groomer shaft from turning when
installing driven pulley,use wrench on groomer shaft
flats.
H. Apply antiseize lubricant to splines of groomer
shaft and slide driven pulley onto groomer shaft. Se-
cure with flange nut. Torque flange nut from 17 to 21
ft--lb (23 to 28 N--m).
DPA Groomer
Page 7.3 -- 8 Rev. E
Reelmaster 6500--D/6700--D
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro Reelmaster 6500-D, Toro Reelmaster 6700-D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Product Type | Walk Behind Mower |
| Engine Manufacturer | Toro |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)