12.Mount
washer(s) and axle pivot pin. Secure the axle pivot pin
in place with the thrust washer and jamnut.
the axle to the frame with the axle pin. Install
5
6
7
13.Remove
floor.
thejackstandsandlowerthemachinetothe
6
5
8
10
14.Lubricate
the steering spindles through the grease
4
9
3
fittings on the rear axle.
2
15.Install
the hydraulic hoses to the steering cylinder.
steering cylinder hydraulic connections for
1
16.Check
leaks.
Figure 14
1.
2.
3.
4.
5.
Cotter pin
Dust cap
Bearing buddy
Seal
Bearing cone
6.
7.
8.
9.
Bearing race
Wheel hub
Washer
Wheel Bearings
Rear wheel bearing buddies should be lubricated every
Retainer
10. Locknut
50
operatinghours.Disassemble,clean,repackandad-
justthe rear wheel bearings after 800 hours ofoperation
or once a year. Use No. 2 general purpose lithium
grease containing E.P. additive. If operating conditions
are extremely dusty and dirty, it may be necessary to
perform this maintenance more often.
8.
Install remaining bearing into the bearing cup.
Pack inside of wheel hub with some grease (not full).
9.
in place with the flat washer and slotted nut. DO NOT
tighten the nut or install the cotter pin.
Slide the wheel onto the spindle shaft and secure it
1.
floor. Support the machine with jack stands or blocks to
prevent it from falling.
Jack up the rear of the machine until the tire is off the
10.Rotate
the wheel by hand and tighten the slotted nut
(Fig. 14) to 75 to 100 in-lb (8.5 to 11.3 Nm) to set the
bearing. Then, loosen the nut until the hub has end play.
2.
Remove the dust cap and bearing buddy from the
end of the wheel spindle (Fig. 14).
11.
Rotate the wheel by hand and re-tighten the slotted
nut to 15 to 20 in-lb (1.7 to 2.3 Nm).
3.
Remove the cotter pin, retainer, slotted nut, and
washer. Slide the wheel off spindle shaft.
12.If
necessary rotate the slotted nut counterclockwise
to align slot with cotter pin hole in spindle, and install re-
tainer and cotter pin.
4.
5.
hub. Clean the bearings in solvent. Make sure the bear-
ings are in good operating condition. Clean the inside of
the wheel hub. Check the bearing cups for wear, pitting
or other noticeable damage. Replace worn or damaged
parts.
Pull the seal out of the wheel hub.
Remove the bearings from both sides of the wheel
13.Remove
floor.
jack stands or blocks and lower machine to
14.Fill
the inside of the bearing buddy with grease.
Install bearing buddy and dust cap.
6.
press themintothehubuntiltheyseatagainsttheshoul-
der.
If bearing cups were removed from the wheel hub,
7.
Pack both bearings with grease. Install one bearing
into the cup on inboard side of the wheel hub. Lubricate
the inside of the new lip seal and press it into the wheel
hub.
IMPORTANT: The lip seal must be pressed in so it is
flushwiththeendofthehub.Thelipofthesealmust
be toward the bearing.
Reelmaster 6500-D/6700-D
Page 6 - 13
Axles, Planetaries and Brakes (Rev. C)
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro Reelmaster 6500-D, Toro Reelmaster 6700-D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Product Type | Walk Behind Mower |
| Engine Manufacturer | Toro |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)