Removal (Fig. 61)
Park themachine onalevelsurface, engage parking
brake, lower cutting units and stop engine. Remove key
from the ignition switch.
9. Remove three (3) flange head screws that secure
manifold to machine frame.
1.
10.Remove manifold block from machine.
11.
Ifnecessary,removehydraulicfittingsfrommanifold.
2.
Installing Hydraulic System Components at the begin-
ning of the Service and Repairs section of this chapter.
Read the General Precautions for Removing and
Discard any removed o--rings.
Installation (Fig. 61)
1.
If fittings were removed from mow control manifold,
3.
in the raised position.
Tiltoperatorseatandengageseatproptoretainseat
lubricate and place new o--rings to fittings. Install fittings
into manifold (see Hydraulic Fitting Installation in the
General Information section of this chapter).
4.
5.
sembly purposes. Thoroughly clean hydraulic connec-
tions prior to loosening hydraulic lines.
Locate hydraulic mow control manifold.
Label all hydraulic and electrical connections for as-
2. Position mow control manifold to frame. Install three
(3) flange head screws but do not fully tighten.
3.
Remove caps and plugs from disconnected lines
and fittings.
CAUTION
4.
Lubricate and install new o--rings on manifold fit-
tings. Connect hydraulic lines to hydraulic fittings on
manifold. Properly tighten all connections (see Hydrau-
lic Fitting Installation in the General Information sec-
tion).
Before opening hydraulic system, operate all hy-
draulic controls to relieve system pressure and
avoid injury from pressurized hydraulic oil. See
Relieving Hydraulic System Pressure in the Gen-
eral Information section of this chapter.
5. Secure hydraulic manifold to frame by tightening
three (3) flange head screws.
6.
manifold. Allow lines to drain into a suitable container.
Remove and discard o--rings from fittings.
Disconnect hydraulic hoses and lines from fittings in
6.
switches on manifold.
Plug wire harness leads to solenoid coils and
7.
8.
Lower operator seat.
7.
to prevent contamination.
Putcaps or plugs on disconnected hoses andfittings
Check oil level in hydraulic reservoir and add correct
oil if necessary.
8.
Unplug wire harness leads from solenoid coils and
switches on manifold.
9.
Follow Hydraulic System Start--up procedures (see
Hydraulic System Start--up in this section).
Reelmaster 5010 Series
Page 4 -- 75
Hydraulic System
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work