Front Roller
Removal (Fig. 28)
1
Loctite #242
1.
Position machine on a clean and level surface, lower
cutting units, stop engine, engage parking brake and re-
move key from the ignition switch.
Antiseize
Lubricant
2.
Remove the cutting unit from the machine and place
2
on a level working surface. Use cutting unit kickstand
(see Special Tools) to raise front roller from work sur-
face.
15 to 19 ft--lb
(20 to 26 N--m)
3
5
3.
Loosen flange nut and cap screw securing the front
roller shaft to each front height--of--cut (roller) bracket.
6
Loctite #242
4.
On one of the height--of--cut (roller) brackets:
7
4
A. Remove flange lock nut and carriage screw that
secure bracket to the cutting unit side plate.
8
B. Remove the height--of--cut (roller) bracket from
the cutting unit.
5.
height--of--cut (roller) bracket on the cutting unit.
Slide the front roller assembly from the remaining
Figure 28
1.
Cap screw
5.
6.
7.
8.
Carriage screw
Cap screw
Flange nut
Front roller assembly
2.
3.
4.
Flat washer
6.
er) bracket from the cutting unit.
If necessary, remove the second height--of--cut (roll-
Flange lock nut
HOC (roller) bracket
4.
Slide front roller shaft into bracket attached to the
Installation (Fig. 28)
cutting unit. Slide second height--of--cut (roller) bracket
ontotheotherendofroller shaft.Secure secondbracket
to cutting unit side plate with carriage screw and flange
nut.
1.
Place cutting unit on a level working surface and use
cutting unit kickstand (see Special Tools) to support cut-
ting unit.
2.
height--of--cut (roller) brackets. Replace cap screw(s) if
necessary:
Inspect condition of cap screws (item 1) in both
5. Apply Loctite #242 (or equivalent) to exposed
threads of cap screw (item 1) between flange of side
plate and position of flange lock nut (item 3) on cap
screw. Tighten flange lock nut on cap screw and then
loosennut1/4to1/2turn.Capscrewshouldrotatefreely
with little (if any) endplay after lock nut installation.
A. Place two (2) flat washers on cap screw and
thread flange lock nut onto cap screw to a position
0.750”
(19 mm) from screw head.
6.
Apply Loctite #242 (or equivalent) to threads of two
B. Apply antiseize lubricant to cap screw threads
that will extend into height--of--cut (roller) bracket.
(2) cap screws (item 6). Center front roller to the cutting
reel and secure in place with two (2) cap screws. Torque
cap screws from 15 to 19 ft--lb (20 to 26 N--m). Secure
cap screws with flange nuts.
C. Thread cap screw into bracket.
NOTE: When assembling height--of--cut (roller) brack-
etstosideplate,makesurethatcapscrewheadandone
washer are above adjustment flange on side plate and
second washer and flange lock nut are below flange.
7.
Lubricate front roller.
8. Adjust cutting unit (see Cutting Unit Operator’s
Manual).
3.
If both front height--of--cut (roller) brackets were re-
moved from cutting unit side plate, position one of the
brackets to side plate. Secure bracket to side plate with
carriage screw and flange lock nut.
Cutting Units
Page 7 -- 28
Reelmaster 5010 Series
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work