Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual

Reel Bearing Adjustment
Toinsure cutquality and long life of thecutting reel bear-
ings, periodically check reel bearing adjustment.
4.  With the cutting unit and reel in a horizontal position,
use a13/8”socket  andtorque wrench toovertighten the
bearing adjuster nut to 25 in--lb (2.8 N--m).
Check Reel Bearing Adjustment
5.
bearing adjuster  nut from  15 to 17  in--lb (1.7  to 1.9
N--m).
Loosen the  bearing  adjuster nut  and then  torque
1.
Hydraulic Reel Motor Removal in the Service and Re-
pairs section of this chapter).
Remove hydraulic reel motor from cutting unit (see
6.
Using a suitable torque wrench and spline insert tool
2.
exists (see Cutting Unit Operator’s Manual).
Loosen bedknife to reel adjustment until no contact
(see Special Tools), check that reel rolling torque does
not exceed 10 in--lb (1.1 N--m). Also, check if reel bear-
ing endplay exists. If endplay exists, replace the cutting
reel bearings and seals (see Reel Assembly and Reel
Assembly Service in the Service and Repairs section of
this chapter).
CAUTION
Contact with the reel, bedknife or other cutting
unit  parts  can result  in  personal  injury.  Use
heavy gloves when handling the cutting reel.
7.
Apply Loctite #242 (or equivalent) to threads of set
screw and secure bearing adjuster nut in place with set
screw. Torque set screw from 12 to 15 in--lb (1.4 to 1.7
N--m).
3.
sembly side to side. If reel end play exists, side to side
movement will be detected.
Hold on to the reel shaft and try to move the reel as-
8.
ting unit components to cutting unit.
Afterreelbearingadjustment,installallremovedcut-
4.
Using a suitable torque wrench and spline insert tool
4
(see Special Tools),  measure the rolling resistance of
the cutting reel. Cutting reel rolling torque should notex-
ceed 10 in--lb (1.1 N--m).
12 to 15 in--lb
(1.4 to 1.7 N--m)
1
5.
Ifreelhasendplayorifrollingtorqueisincorrect,per-
form reel bearing adjustment (see below).
6.
ting unit (see Cutting Unit Operator’s Manual).
After checking or adjusting reel bearings, adjust cut-
7.
draulic Reel Motor  Installation in the Service  and Re-
pairs section of this chapter).
Install hydraulic reel  motor to cutting unit (see  Hy-
15
(1.7
to 17 in--lb
to 1.9 N--m)
Reel Bearing Adjustment (Fig. 11)
3
2
1.
Make sure that no contact exists between bedknife
and reel.
Figure 11
1.
2.
LH side plate
Threaded insert
3.
4.
Bearing adjuster nut
Set screw
2.
Remove cutting unit components on LH side plate to
allow access to  bearing adjuster nut.  If cutting unit is
equipped with a rear  roller brush, refer to Rear Roller
Brush (Optional) in the Service and Repairs section of
this chapter. If cutting unit is equipped with a groomer,
refer to Chapter 8 -- Groomer.
3.
Loosen set screw that secures bearing adjuster nut
in LH side plate of cutting unit.
IMPORTANT: Over tightening reel bearing adjuster
nut may damage reel bearings.
Cutting Units
Page 7 -- 12
Reelmaster 5010 Series
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 292 pages
Document TypeCatalog, Service Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual SKU UPC Model
Alfredo Gonzalez on Jun 06, 2014.

i hope is going to work


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website