Disassembly (Fig. 7)
3. Fillwheelhubcavitybetweenbearingsapproximate-
ly50%fullofgrease.Position remainingbearing intothe
outer bearing cup.
1.
Chock frontwheelstopreventmachine fromshifting.
2.
tion). Make sure to support machine with jack stands.
Remove rear wheel (see Wheel Removal in this sec-
4.
and secure it in place with the tab washer and jam nut.
DO NOT fully tighten the nut or install the cotter pin.
Slide the wheel hub assembly onto the spindle shaft
3.
4.
Remove the dust cap from the wheel hub.
5.
nutfrom 75 to 100 in-lb (8.5 to 11.3N--m) to set thebear-
ings. Then, loosen the nut until the hub has endplay.
While rotating the wheel hub by hand, torque the jam
Remove the cotter pin, retainer, jam nut and tab
washer. Slide the wheel hub from the spindle shaft.
5.
Pull the seal out of the wheel hub. Discard seal.
6.
While rotating the wheel hub by hand, torque the jam
nutfrom15to20in-lb(1.7to2.3N--m).Aftertightening,
make sure that the wheel hub does not have any free
play.
6.
Remove the bearing cones from both sides of the
wheelhub.Cleanthe bearings in solvent. Make surethe
bearings are in good operating condition. Clean the in-
side of the wheel hub. Check the bearing cups for wear,
pitting or other damage. Replace worn or damaged
parts.
7.
Install retainer with slot aligned to cotter pin hole in
spindle. Install cotter pin.
8.
dust cap.
Fill dust cap approximately half full of grease. Install
Assembly (Fig. 7)
1.
press new cups into the hub until they seat against the
shoulder of the hub.
If bearing cups were removed from the wheel hub,
9.
tion).
Install rear wheel (see Wheel Installation in this sec-
10.Lower
machine to ground.
IMPORTANT: The lip of the seal must be toward the
bearing. The seal should be pressed in so it is flush
with the end of the wheel hub.
11.
Torque lug nuts evenly in a crossing pattern from 70
to 90 ft--lb (95 to 122 N--m).
2.
Pack both bearings with grease. Install one bearing
into the bearing cup on inboard side of the wheel hub.
Lubricate the inside of a new seal and press it into the
wheel hub with the seal lip toward the bearing.
Reelmaster 5010 Series
Page 6 -- 11
Chassis
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work