7.
and secure with four (4) flange head screws and flange
nuts.
Position steering column brace (item 13) to machine
CAUTION
8.
Slide rubber bellows to bottom of steering column.
Before opening hydraulic system, operate all hy-
draulic controls to relieve system pressure and
avoid injury from pressurized hydraulic oil. See
Relieving Hydraulic System Pressure in the Gen-
eral Information section of this chapter.
9.
shroud (Fig. 82). Position shroud in place and secure
with removed fasteners.
Place rubber bushings and spacers into holes of
10.Check
oil if necessary.
oil level in hydraulic reservoir and add correct
7.
valve. Allow lines to drain into a suitable container.
Disconnect hydraulic lines from steering control
11.
Hydraulic System Start--up in this section).
Follow Hydraulic System Start--up procedures (see
8.
to prevent contamination.
Put caps or plugs on disconnected lines and fittings
2
9.
Loosen and remove remaining two (2) flange head
3
screws and flange nuts that secure steering column to
machine.
4
1
10.Remove
steering column assembly (Fig. 4) with
steering control valve attached from machine.
11.
Loosen andremove four (4) socket head screws that
secure steering control valve to steering column.
5
12.Remove
umn.
steering control valve from steering col-
6
13.If
necessary,remove fittings and O--rings from steer-
ing control valve. Discard all removed O--rings.
7
Installation (Fig. 81)
1.
If fittings were removed, lubricate new O--rings with
clean hydraulic oil and install fittings to steering control
valve (see Hydraulic Fitting Installation in the General
Information section of this chapter).
Figure 82
2.
trol valve shaft.
Apply antiseize lubricant to splines of steering con-
1.
2.
3.
4.
Shroud
5.
6.
7.
Lock nut (2 used)
Rubber bushing (2 used)
Spacer (2 used)
Screw (2 used)
Flat washer (2 used)
Phillips screw (2 used)
3.
Slide steering control valve shaft into steering col-
umn universal joint. Position control valve with ports to-
ward front of machine. Secure steering control valve to
steering column with four (4) socket head screws. Hand
tighten screws in a crossing pattern and then torque
screwsagaininacrossingpatternfrom7to10ft--lb(9.5
to 13.5 N--m).
L
T
4.
cure steering column in place with two (2) flange head
screws and flange nuts at rear two mounting holes.
Position steering column assembly to machine. Se-
5.
Remove caps and plugs from disconnected lines
and fittings.
R
6.
tofittingsonsteeringcontrolvalve.Tightenconnections.
Lubricate new O--rings and connect hydraulic lines
P
Figure 83
Reelmaster 5010 Series
Page 4 -- 99 Rev. B
Hydraulic System
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work