Backlapping
8.
When the backlap operation is completed, shut off
DANGER
engine and rotate directional valve lever fully (90o from
the backlap position) to the F (forward) position. Also,
rotate flow control valve knob to correct mowing posi-
tion.
TO AVOID PERSONAL INJURY OR DEATH:
Never place hands or feet in the reel area
while the engine is running.
While backlapping, the reels may stall and
then restart.
D
9.
Wash all lapping compound from the cutting units.
a better cutting edge, run a file across the front
D
10.For
D
foot.
D
running.
Do not attempt to restart reels by hand or
face of the bedknife when the lapping operation is com-
pleted. This will remove any burrs or rough edges that
may have built up on the cutting edge.
Do not adjust reels while the engine is
D
If a reel stalls, stop engine before
NOTE: Additional instructions and procedures on
backlapping are available in the Toro General Service
Training Book, Reel Mower Basics (part no.
attempting to clear the reel.
D
Reelmotorsareconnectedinseries:rotating
one motor causes rotation in other motors.
09168SL)
.
1.
Position machine on a clean and level surface, lower
cutting units, stop engine, engage parking brake and re-
move key from the ignition switch.
4
3
2.
On all cutting units, make initial reel to bedknife ad-
TO BACKLAP
TO BACKLAP
justments appropriate for backlapping.
IMPORTANT: Do not attempt to rotate the direction-
alvalveleveronthehydraulicmowcontrolmanifold
when the engine or reels are running.
5
2
3.
Raise seat, locate hydraulic mow control manifold
and rotate directional valve lever fully to the R (backlap)
position (Fig. 16).Rotate flowcontrol valve knob toposi-
tion 1.
1
FRONT
4.
RPM).
Start engine and run at low idle speed (1150 to 1350
Figure 16
1.
2.
3.
Mow control manifold
Rear directional lever
Rear flow control
4.
5.
Front flow control
Front directional lever
5.
LOWER--MOW control forward to start the cutting reels.
Press PTO switch to engage and move RAISE/
6.
Apply lapping compound to cutting reel blades with
Top Face
a long handled brush (see Special Tools). While back-
lapping, occasionally move brush across reel to distrib-
ute compound.
Remove
Burr
Relief Angle
Front
Face
Front Angle
CAUTION
Be careful when backlapping the reel because
contact with the reel or other moving parts can
result in personal injury.
Figure 17
7.
Tomakeacuttingunitadjustmentwhilebacklapping,
turn reels OFF, shut off engine and wait for all machine
and cutting unit motion to completely stop. Then, after
cutting unit adjustments have been completed, repeat
steps 4 through 6.
Reelmaster 5010 Series
Page 7 -- 15 Rev. B
Cutting Units
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work