Fuel Pump
The Reelmaster fuel pump is attached to the inside of
the left side frame rail near the fuel tank (Fig. 65).
7. Replace fuel pump if necessary. Install fuel hose to
the fuel/water separator. Make sure to secure fuel hose
with hose clamp.
IMPORTANT: When testing fuel pump, make sure
that pump is not operated without fuel.
8. Connect harness electrical connector to the engine
fuel stop solenoid.
DANGER
9. Bleed the fuel system.
10.Lower
and secure operator seat and hood.
Becausedieselfuelishighlyflammable,usecau-
tionwhenhandlingit.Donotsmokewhiletesting
thefuelpump.Donottestfuelpumpwhileengine
is hot. Make sure that there is adequate ventila-
tion when testing. Always wipe up any spilled
fuel before starting the engine.
Fuel Pump Specifications
Fuel pump specifications for machines with serial num-
bers below 280000000 are as follows:
Pump Capacity
Pressure
23.5 fl oz/min (700 ml/min)
3.3 PSI (22.8 kPa)
0.9 amp
Fuel Pump Capacity Test
Current Draw
1.
Park machine on a level surface, lower cutting units,
stop engine and engage parking brake. Remove key
from ignition switch. Raise operator seat and hood.
Fuel pump specifications for machines with serial num-
bers above 280000000 are as follows:
2.
engine fuel stop solenoid to prevent the engine from
starting (see Fuel Stop Solenoid in this section).
Disconnect harness electrical connector from the
Pump Capacity
Pressure
64 fl oz/min (1.9 liters/min)
7 PSI (48.3 kPa)
2.0 amp
3.
Disconnect fuel hose (pump discharge) from the
Current Draw
fuel/water separator inlet fitting (Fig. 66).
4.
filter and fuel tank suction tube screen are free of ob-
structions.
Make sure fuel hoses attached to the fuel pump, fuel
2
5.
inder sufficient enough to collect 1 quart (0.95 liter).
Place disconnected hoseinto alarge, graduated cyl-
1
2
IMPORTANT: When testing the fuel pump, DO NOT
turn ignition switch to START.
Note:
Conversion Kit will have the same fuel pump as ma-
chines with serial numbers above 280000000.
Machines that are equipped with a Biodiesel
Figure 65
2.
1.
Fuel pump
Pump discharge hose
6.
tion switch to the RUN position. Allow pump to run for
time listed below, then return switch to OFF.
Collect fuel in the graduated cylinder by turning igni-
3
2
A. For machines with serial numbers below
280000000,
the amount of fuel collected in the grad-
uated cylinder should be approximately 11.8 fl oz
ml) after thirty (30) seconds.
(350
B. For machines with serial numbers above
280000000, the amount of fuel collected in the grad-
1
uated cylinder should be approximately 16 fl oz (475
ml) after fifteen (15) seconds.
Figure 66
1.
2.
Fuel/water separator
3.
Inlet fitting
Fuel hose (from pump)
Reelmaster 5010 Series
Page 5 -- 45 Rev. B
Electrical System
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work