Joystick Raise and Lower Switches
Two micro switches for the joystick are located on the lift
control that is attached to the control arm. The rear
switch on the control is used to lower (and engage) the
cutting units and the front switch to raise (and disen-
gage) them. A normally open contact in the switch
closes when the joystick is positioned to either lower or
raisethecuttingunits.Eachswitchhasanelectricalcon-
nector to make sure the normally closed contact on the
switch is not used. The raise switch has yellow/black
and black harness wires connected to it and the lower
switch has orange and black harness wires connected
to it.
H. If the joystick switch tests correctly and a circuit
problem still exists, check wire harness (see Wiring
Schematic and Circuit Drawings in Chapter 9 -- Elec-
trical Diagrams).
I. Connect harness electrical connector to the joys-
tick switch.
J. Install control arm covers to machine (see Con-
trolArmAssemblyintheServiceandRepairssection
of this chapter).
Testing
1.
Before disconnecting the joystick switches for test-
1
FRONT
ing,theswitches andtheircircuitwiringshould betested
as an ECM input with the Diagnostic Display (see Diag-
nostic Display in the Troubleshooting section of this
chapter).
3
2.
If the Diagnostic Display verifies that the joystick
switches and circuit wiring are functioning correctly, no
further switch testing is necessary.
2
3.
tick switch and circuit wiring are not functioning correct-
If the Diagnostic Display determines that either joys-
ly, test joystick switches as follows:
Figure 39
A. Remove control arm covers to gain access to
joystick switches (see Control Arm Disassembly in
the Service and Repairs section of this chapter).
1.
2.
Joystick
Lower switch
3.
Raise switch
B. Make sure ignition switch is in the OFF position.
3
1
C. Disconnect harness electrical connector fromthe
raise or lower switch that is to be tested (Fig. 39).
D. Connect a multimeter (ohms setting) across the
normally open (NO) and common terminals of the
switch (Fig. 40).
2
E. With the joystick in the neutral (center) position,
there should be no continuity across the switch ter-
minals.
4
F. Move and hold the joystick to activate the switch
being tested. There should be continuity across the
switch terminals.
Figure 40
3.
4.
1.
2.
NO terminal
Common terminal
NC terminal (not used)
Switch lever
G. If joystick switch is faulty, replace switch.
Electrical System
Page 5 -- 32 Rev. B
Reelmaster 5010 Series
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work