3.
new components noting proper orientation as shown in
Figures 41 and 42.
If drive bearing housing was disassembled, install
8
A. Installbearingonshaftbypressingequally onthe
inner and outer bearing races. Install the bearing so
that the bearing seal is closest to the shoulder on the
shaft. Install snap ring (item 6) onto shaft to retain
bearing.
7
6
9
B. Install new grease seal into housing with the lip of
the seal toward the drive shaft splines. Apply grease
to lip of seal.
5
3
2
4
C. Fill cavity between bearing location and grease
seal 50% to 75% full with high temperature Mobil
XHP--222 grease (or equivalent).
1
9
10
Figure 41
D. Carefully slide shaft and bearing fully into pivot
hub bore taking care to not damage the grease seal.
Install retaining ring (item 5) to secure bearing in piv-
ot hub.
1.
2.
3.
4.
5.
Bearing housing
Drive shaft
Ball bearing
Grease seal
Retaining ring
6.
7.
8.
9.
Snap ring
O--ring
Side plate
Socket head screw
10. Grommet
4.
Assemble roller brush components using Figure 38
as a guide.
Fill cavity
A. Apply a light coating of grease to inner diameter
of the grommet in drive bearing housing.
50
to 75% full
with grease
1
5
B. Apply Loctite #242 (or equivalent) to threads of
flangeheadscrew(item20)thatsecures drivepulley
to drive shaft.
2
C. Torque flange head screw (item 20) that secures
drive pulley to drive shaft from 27 to 33 ft--lb (37 to
44
N--m).
D. Apply antiseize lubricant to square key that lo-
cates driven pulley onto roller brush shaft.
6
E. Torque flange nut (item 11) that secures driven
pulley to roller brush shaft from 17 to 21 ft--lb (23 to
3
4
28
N--m).
F. Check alignment of pulleys with a straight edge
placed along the outer face of the driven pulley (Fig.
Figure 42
4.
5.
6.
43).
The outer faces of the driven and drive pulleys
(not the idler pulley) should be in line within 0.030”
mm). If necessary to align pulleys, remove driv-
1.
2.
3.
Bearing housing
Drive shaft
Ball bearing
Grease seal
Retaining ring
Snap ring
(.76
en pulley from brush shaft and add or remove wash-
er(s) (item 9) until drive and driven pulleys are
aligned.
G. Position excluder seals on brush shaft so that
seals just touch bearing housings.
H. To tension drive belt, make sure idler pulley lock
nut is loose. Lift up on idler plate tab with 15 lbs of
force for a new belt (10 lbs of force for a used belt)
and tighten pulley lock nut. Refer to decal on brush
plate (Fig. 44).
Cutting Units
Page 7 -- 36 Rev. A
Reelmaster 5010 Series
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work