Height Adjuster Assembly
11
12
10
9
8
Antiseize
Lubricant
7
13
30
(3.4
to 40 in--lb
to 4.5 N--m)
6
14
Antiseize
Lubricant
5
4
3
17 to 21 ft--lb
(23 to 28 N--m)
2
Antiseize
Lubricant
1
Figure 16
1.
2.
3.
4.
5.
Groomer plate (LH drive shown)
Shoulder bolt
6.
Flange head screw
11. Flat washer
12. Groomer adjuster
13. Detent spring
7.
8.
9.
Lower ramp
Ball joint rod
External snap ring
Upper ramp
Jam nut
Compression spring
14. Washer head screw
10. Bushing
NOTE: The groomer reel drive is located on the oppo-
site side of the cutting unitfrom the cutting reel hydraulic
motor. Figure 16 shows components used when the
groomer reel drive is on the left side of the cutting unit.
B. If jam nuts (item 4) were removed from ball joint
rod, apply antiseize lubricant to threads of rod where
jam nuts will be positioned. Install jam nuts so that
distance from end of ball joint rod to top of upper nut
is from 3.060” to 3.180” (7.8 to 8.0 cm).
Disassembly (Fig. 16)
C. Apply antiseize lubricant to threads of groomer
adjuster (item 12) before installing it on threads of
ball joint rod.
1.
Park machine on a clean and level surface, lower
cutting units completely to the ground, stop engine, en-
gage parking brake and remove key from the ignition
switch.
D. If detent spring (item 13) was removed, secure
detentspringtoupperrampwithwasherheadscrew.
Torque screw from 30 to 40 in--lb (3.4 to 4.5 N--m).
2.
guide.
Disassemble height adjuster using Figure 16 as a
2.
bolt(item2).Torqueshoulderboltfrom17to21ft--lb(23
to 28 N--m).
Secure ball joint rod to groomer plate with shoulder
3.
age. Replace all worn or damaged components.
Clean all components and inspect for wear or dam-
Assembly (Fig. 16)
3.
Check groomer reel height and adjust as needed.
1.
noting the following items:
Assemble height adjuster using Figure 16 as aguide
4.
After groomer height has been adjusted, adjustloca-
tion of jam nuts so compression spring length is 1.375”
cm) when the groomer handle is in the disengaged
position (handle toward rear of cutting unit).
(3.5
A. If bushing (item 10) was removed from upper
ramp, press new bushing into housing fully to the
shoulder in the bore.
Groomer
Page 8 -- 16
Reelmaster 5010 Series
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work