Axle Pivot Bushings (Fig. 9)
4. Remove the flange head screw, spindle cap and re-
taining ring that secure the wheel spindle into the axle
tube. Slide the spindle and wheel assembly out of the
axletubetoexposethespindlebushings.Locateandre-
trieve thrust washer (item 19) from wheel spindle shaft.
The rear axle must be held in place snugly by the axle
pivot pin. Excessive movement of the axle, which is
characterized by erratic steering, might indicate worn
axle pivot bushings. To correct the problem, replace the
bushings (item 36).
5. Use a bushing removal tool to extract both bushings
from the axle tube. Take care to not damage the bore of
theaxletube.Cleantheinsideoftheaxletubetoremove
any dirt or foreign material.
1.
Remove rear axle from machine (see Rear Axle Re-
moval in this section).
2.
Use a bushing removal tool to extract both axle pivot
6.
Apply grease to the inside and outside of the new
bushings from the axle pivot tube. Take care to not dam-
age bore of pivot tube during bushing removal. Clean
theinsideofthetubetoremove dirtandforeignmaterial.
bushings. Use an arbor press to install the bushings into
the top and bottom of the axle tube. Press bushings into
tube until flange shoulder bottoms on tube.
3.
Apply grease to the inside and outside of the new
7.
spindle for wear and replace if worn or damaged.
Thoroughly clean the spindle shaft. Inspect the
bushings. Use an arbor press to install the bushings into
the front and back of the axle pivot tube. Bushings must
be flush with the axle tube.
8. Install thrust washer (item 19) onto the spindle shaft
and slide the shaft up through the axle tube. Hold the
wheelandspindleshaftassemblyinplaceandinstallthe
retaining ring (item 13) onto the end of the spindle shaft.
4.
tion in this section).
Install rear axle to machine (see Rear Axle Installa-
Rear Axle Spindle Bushings (Fig. 9)
9.
Install the spindle cap and flange head screw.
The rear wheel spindles must fit snugly in the rear axle.
Excessive movement of the spindle in the axle might in-
dicate that the spindle bushings (item 43) are worn and
must be replaced.
10.Connect
hex nut and cotter pin.
the tie rod end to the drag link with slotted
11.If separated, secure steering cylinder ball joint to
drag link with slotted hex nut and cotter pin.
1.
Remove rear axle from machine (see Rear Axle Re-
moval in this section).
12.Install rear axle to machine (see Rear Axle Installa-
tion in this section).
2.
Remove cotter pin and slotted hex nut that secure
the tie rod end to the drag link. Separate the tie rod end
from the drag link.
13.Lubricate the steering spindles through the grease
fittings on the rear axle.
3.
If right side spindle is being removed, remove cotter
14.Check rear wheel toe--in (see Traction Unit Opera-
tor’s Manual).
pin and slotted hex nut that secure steering cylinder ball
joint to drag link. Separate steering cylinder from drag
link.
15.After
all adjustments have been made, make sure
that no contact is made between any machine compon-
ents as the wheels are moved from lock to lock. Re-
adjust if necessary.
Reelmaster 5010 Series
Page 6 -- 15
Chassis
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work