B. Push down and rearward on the spring end to un-
hook the spring from the stop on the lift arm.
4. Align lift cylinder rod end to lift arm mounting slot.
Slide cylinder pin (item 30) with retaining ring (item 32)
and thrust washer (item 31) through the lift cylinder and
lift arm. Install second thrust washer on pin and secure
with second retaining ring.
6.
Disconnect hydraulic lift cylinder rod end clevis from
liftarm(seeLiftCylinderRemovalintheServiceandRe-
pairs section of Chapter 4 -- Hydraulic System). Pivot lift
cylinder rod end away from lift arm.
CAUTION
7.
Remove lynch pin (item 12) and thrust washer (item
13) from rear of pivot yoke. Slide pivot yoke assembly
Be careful when applying tension to the torsion
spring on the rear lift arms. The spring is under
heavy load and may cause personal injury.
from lift arm. Locate and retrieve front thrust washer
(item 13).
8.
Remove two (2) flange head screws (item 6) that se-
curespring catch tomachine. Remove spring catch, tor-
sion springs (items 23 and 24), two (2) spacers (item 1)
and two (2) washers (item 25).
5.
Apply tension to torsion springs.
A. Insert nut driver or small piece of pipe onto the
long leg ofthetorsion spring on therear ofthe liftarm
pivot pin.
9.
to frame.
Remove washer head screw that secures pivot pin
B. Pushdownandforward onthespringendtohook
the spring to the stop bolt on the lift arm.
10.Support
pivot pin from frame and lift arm. Remove rear lift arm.
rear lift arm to prevent it from falling. Slide
6.
Mount cutting unit to lift arm.
11.
Inspect bushings in lift arm and pivot yoke for wear
ordamage.Ifnecessary,replacebushings(Figs.20and
21).
7. Lubricate lift arm grease fittings.
A. Use bushing removal tool to extract both bush-
ings from the lift arm or pivot yoke. Take care to not
damage the bore.
3
B. Clean the inside of the bore to remove any dirt or
foreign material.
1
C. Apply grease to the inside and outside of the new
bushings.
3
D. Use an arbor press to install the bushings into lift
arm or pivot yoke. Lift arm bushings should be
pressed until bushing flange is against lift arm bore.
The upper pivot yoke bushing should be pressed ful-
ly to the shoulder in the pivot yoke bore. The lower
pivot yoke bushing should be flush with the yoke
tube.
2
2
Figure 20
1.
2.
Rear lift arm (LH shown)
Pivot yoke bushing
3.
Lift arm bushing
Installation (Fig. 19)
2
1
1.
Position rear lift arm to frame and slide pivot pin
through frame bosses and lift arm. Secure pin with
washer head screw.
3
2.
each pivot pin. Position long leg of spring forward and
pointing out from top of spring.
Place washer, spacer and torsion spring over rear of
4
Figure 21
3.
4.
3.
Position spring catch to pivot pins and secure with
1.
2.
Pivot yoke
Upper bushing
Pivot yoke shoulder
Lower bushing
two (2) flange head screws (item 6). Make sure that
short end of torsion springs are against stop on spring
catch.
Reelmaster 5010 Series
Page 6 -- 23
Chassis
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work