3.
Using a spanner wrench, rotate head clockwise until
2. Coat new O--rings, back--up washer and other seals
with clean hydraulic oil.
theedgeoftheretaining ringappears inthebarrelopen-
ing. Insert a screwdriver under the beveled edge of the
retainingringtostarttheretainingringthroughtheopen-
ing. Rotate the head counter--clockwise to remove re-
taining ring from barrel and head.
A. Carefully install cap seal and O--rings to the pis-
ton.
B. Carefully install back--up washer, O--ring, u--cup
and wiper to the head.
4.
Remove plugs from ports. Extract shaft, head and
piston by carefully twisting and pulling on the shaft.
IMPORTANT: Do not clamp vise jaws against the
shaft surface. Clamp on the clevis ONLY.
IMPORTANT: Do not clamp vise jaws against the
shaft surface. Clamp on the clevis ONLY.
3.
Mountshaftsecurelyinavisebyclampingonthecle-
vis of the shaft.
5.
Mountshaftsecurelyinavisebyclampingonthecle-
vis of the shaft. Remove lock nut and piston from the
shaft. Carefully slide head off the shaft.
A. Coat shaft with clean hydraulic oil.
B. Slide head onto the shaft.
6.
Taking care to not scratch or damage the piston, re-
move cap seal and O--rings from the piston.
C. Install piston onto the shaft and secure with lock
nut. Torque lock nut from 30 to 35 ft--lb (41 to 47
N--m).
7.
Taking care to not scratch or damage the head, re-
move O--ring, back--up washer, wiper and u--cup from
the head.
D. Remove shaft assembly from the vise.
Inspection
IMPORTANT: Prevent damage when clamping the
hydraulic cylinder into a vise; clamp on the clevis
end of the barrel ONLY.
CAUTION
4.
Mount barrel securely in a vise by clamping on the
clevis end of the barrel.
Use eye protection such as goggles when using
compressed air.
IMPORTANT: When installing the head into the bar-
rel, pay careful attention to the retaining ring slot in
thebarreltoinsurethatthepistonandheadsealsdo
not lodge in the slot.
1.
Wash all lift cylinder components in solvent. Dry
parts with compressed air.
2.
out--of--roundness and bending.
Inspect internal surface of barrel for deep scratches,
5. Coat all internal parts with a light coat of clean hy-
draulic oil. Slide piston, shaft and head assembly into
the barrel being careful not to damage the seals.
3.
Inspect head, shaft and piston for excessive pitting,
scoring and wear.
6. Secure head in barrel by installing retaining ring.
Align retaining ring hole in the head with the access slot
in the barrel. Insert the retaining ring hook into the hole
androtateheadclockwise untilthe retaining ring iscom-
pletely pulled into the barrel and the ring ends are cov-
ered.
4.
Replace liftcylinder ifinternal components arefound
to be worn or damaged.
Assembly (Fig. 80)
1.
Make sure all lift cylinder parts are clean before as-
sembly.
Reelmaster 5010 Series
Page 4 -- 97 Rev. B
Hydraulic System
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work