Reel Assembly Removal (Fig. 24)
Position machine on a clean and level surface, lower
11.Inspect and service cutting reel assembly as re-
quired (see Reel Assembly Service in this section).
1.
cutting units, stop engine, engage parking brake and re-
move key from the ignition switch.
2.
Remove the cutting unit from the machine and place
on a flat work area.
3.
If cutting unit is equipped with acounterweight on LH
side plate (as shown in Figure 24), remove the two (2)
capscrewssecuringthecounterweighttothesideplate.
Remove counter weight from the cutting unit. Remove
and discard o--ring from counter weight.
8
1
4.
Ifcutting unitis equipped with anoptional groomer or
rear roller brush, remove components for those options
from left hand side plate of cutting unit. See Service and
Repairs section of Chapter 8 -- Groomer for information
on groomer. See Rear Roller Brush in the Service and
Repairs section of this chapter for information on rear
roller brush.
2
9
4
5
6
3
5.
LH side plate.
Remove the bedbar pivot bolt and washers from the
4
Loctite #242
27
to 33 ft--lb
7
(
37 to 44 N--m)
15 to 19 ft--lb
(20 to 25 N--m)
6.
LHsideplate(seeFrontRollerRemovalandRearRoller
Removal in this section).
Loosen fasteners that secure front and rear rollers to
Figure 25
1.
Carrier frame
Shim (if equipped)
Support tube
Frame spacer
Flat washer
6.
7.
8.
9.
Cap screw
2.
3.
4.
5.
Flange head screw
Rear grass shield
LH side plate
7.
grass shield to LH side plate (Fig. 25).
Remove cap screw and flat washer that secure rear
8.
tube, frame spacer and carrier frame to LH side plate
(Fig. 25).
Remove flange head screw that secures support
Reel Assembly Installation (Fig. 24)
Thoroughly clean side plates and other cutting unit
1.
components. Inspect side plates for wear or damage
and replace if needed.
NOTE: The reel bearings andgrease seals are press fit
on the cutting reel shaft and should remain on the reel
when removing the LH side plate.
NOTE: Check that grease seals on cutting reel shaft
are flush to 0.060” (1.5 mm) away from retaining ring on
reel shaft. If necessary, adjust position of grease seals
to allow proper clearance.
NOTE: Side plates on 5” cutting reel attach to cutting
unit frame with two (2) shoulder bolts and flange nuts.
Sideplateson7”cuttingreelusethree(3)shoulderbolts
and flange nuts.
2.
Make sure that grease seals and bearings are prop-
erly greased and positioned on cutting reel (see Reel
Assembly Service in this section). Apply thin coat of
grease to outside of grease seals and bearings on cut-
ting reel to ease reel installation. Also, apply grease to
bearing bores and threads in side plates.
9.
24)
frame.RemovetheLHsideplatefromthereelshaft,roll-
ers, bedbar and cutting unit frame.
Removeshoulderbolts(item8)andflangenuts(item
that secure the LH side plate to the cutting unit
CAUTION
CAUTION
Contact with the reel, bedknife or other cutting
unit parts can result in personal injury. Use
heavy gloves when removing the cutting reel.
Contact with the reel, bedknife or other cutting
unit parts can result in personal injury. Use
heavy gloves when installing the cutting reel.
10.Carefully
slide the cutting reel with bearings, grease
seals and splined inserts from the RH side plate.
Reelmaster 5010 Series
Page 7 -- 21
Cutting Units
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work