2.
drive side of cutting unit:
Install groomer plate assembly to groomer non--
I. Check pulley alignment by laying a straight edge
along the outer face of the drive pulley (Fig. 7). Drive
and driven pulleys should be in line within 0.030”
A. Carefully position non--drive side groomer plate
onto groomer shaft and slide to cutting unit.
(0.76
mm). If necessary, align pulleys by removing
driven pulley and installing or removing washer(s)
(item 3) between pulley and pulley spacer.
B. Position pivot hub to cutting unit.
J. After pulleys are aligned, install groomer drive
belt and groomer belt cover (see Groomer Belt Re-
placement in this section).
C. Secure groomer components to cutting unit side
plate with two (2) socket head screws (item 7).
D. Installhydraulic reelmotor tocuttingunit(seeHy-
draulic Reel Motor Installation intheService andRe-
pairs section of Chapter 7 -- Cutting Units).
4.
assembly. Reposition excluder seals on groomer shaft
if necessary.
Check that excluder seals just touch groomer plate
3.
of cutting unit:
Install groomer plate assembly togroomer driveside
5.
settings. Adjust as needed.
Checkgroomerreelheightandmowerheight--of--cut
A. Position groomer shim to cutting unit side plate.
Carefully position drive side groomer plate onto
groomer shaft and slide to cutting unit.
6.
Lubricate groomer bearings.
NOTE: After greasing groomer bearings, operate
groomer for 30 seconds, stop machine and wipe excess
grease from groomer shaft and seals.
B. Positionpivothubandidlerplateassemblytocut-
ting unit side plate and secure with two (2) socket
head screws (item 7).
C. Connect extension spring (item 14) to stud on
groomer plate. Make sure that spring is in the stud
groove and that spring hook is positioned toward the
drive pulley.
D. Secure quick--up ball joint rod to drive side
groomer plate with shoulder bolt (Fig. 6). Torque
shoulder bolt from 17 to 21 ft--lb (23 to 28 N--m).
1
E. Slide pulley spacer (item 2) and washer (item 3)
onto groomer shaft.
F. Apply antiseize lubricant to square keys (item 4)
that locate drive and driven pulleys. Position keys
into shaft slots.
2
3
Figure 7
NOTE: To prevent cutting reel from turning when
installing drive pulley, block cutting reel with piece of
wood.
1.
2.
Drive pulley
Driven pulley
3.
Straight edge
G. Apply Loctite #242 to threads of flange head
screw that secures drive pulley to pivot hub shaft.
Slide drive pulley onto shaft and secure with flange
head screw. Torque screw from 27 to 32 ft--lb (37 to
43
N--m).
NOTE: To prevent groomer shaft from turning when
installing driven pulley,use wrench on groomer shaft
flats.
H. Slide driven pulley onto groomer shaft and se-
cure with flange nut. Torque flange nut from 17 to 21
ft--lb (23 to 28 N--m).
Groomer
Page 8 -- 8
Reelmaster 5010 Series
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work