Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual

Mow/Transport Switch
Themow/transport switchisanormally  closedproximity
switch that opens when the mow stop lever is placed in
the transport position. The sensing  plate for the mow/
transport switch is the  mow stop lever. The switch  on
machines with a serial number below 310000000 is dif-
ferent than the switch on machines with serial numbers
above 310000000 but the switch function is the same.
NOTE:  When installing  the mow/transport  switch on
machines with serial numbers below 310000000, place
switch plate tab into switch mounting hole that is closest
to target end of switch.
4.
5.
If mow/transport switch is faulty, replace switch.
If the mow/transport switch tests correctly and a cir-
cuit problem still exists, check wire harness (see Wiring
Schematic and Circuit Drawings in Chapter 9 -- Electri-
cal Diagrams).
Testing
1.
Before disconnecting the  mow/transport switch for
testing, the switch and its circuit wiring should be tested
as an ECM input with the Diagnostic Display (see Diag-
nostic Display  in  the Troubleshooting  section of  this
chapter). If the Diagnostic Display verifies that the mow/
transport switch and circuit wiring  are functioning cor-
rectly,  no further  switch  testing  is  necessary.  If the
Diagnostic Display determines that  the mow/transport
switch and circuit wiring  are not functioning correctly,
proceed with testing procedure.
6.
connected to the mow/transport switch after testing.
Make sure that wire harness electrical connector is
1
SERIAL NUMBER
BELOW 310000000
2.
On machines with serial numbers below 310000000
(Fig. 41), test mow/transport switch as follows:
A.  Make sure ignition switch is in the OFF position.
Disconnect  the wire  harness  electrical connector
from the switch. Check thecontinuity ofthe switch by
connecting a multimeter (ohms  setting) across the
switch connector terminals.
2
B.  There should be continuity (closed) between the
switch terminals when the mow stop lever  is in the
mow  position.  There   should  not  be  continuity
(open) between the switch terminals when the mow
stop lever is in the transport position.
Figure 41
1.
Mow stop lever
2.
Mow/transport switch
1
SERIAL NUMBER
ABOVE 310000000
3.
(Fig. 42), test mow/transport switch as follows:
On machines with serial numbers above 310000000
A.  Turn ignition switch  to the ON  position (do not
start engine) and check LED on cable end of mow/
transport switch.
B.  LED should be illuminated when the mow stop
lever is in the mow position. LED should not be illu-
minated when the mow stop lever is in the transport
position.
2
3
FRONT
C. The distance between the mow/transport switch
andthemow/transportlevershouldbefrom0.040”to
0.100”
(1.1to2.5mm).Ifdistanceisincorrect,loosen
jam nuts that secure switch to machine frame. Posi-
tion switch with jam nuts to allow correct clearance
between  switch  and  lever.  Jam  nuts  should  be
torqued from 162 to 198 in--lb (18.4 to 22.4 N--m).
After jam nuts are tightened, make sure  that clear-
ance has not changed.
5
LED location
4
3
Figure 42
1.
2.
3.
Traction pedal
4.
5.
Lock washer (2 used)
Jam nut (2 used)
Mow/transport lever
Mow/transport switch
Reelmaster 5010 Series
Page 5 -- 33   Rev. B
Electrical System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 292 pages
Document TypeCatalog, Service Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual SKU UPC Model
Alfredo Gonzalez on Jun 06, 2014.

i hope is going to work


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website