6.
sealing surfaces, damaged threads and contamination.
Visually inspect the manifold port for damage to the
E. If handle was removed from spool, position spool
so handle location of spool is between stop pins. Ap-
ply Loctite 603 Retaining Compound (or equivalent)
to threads on handle and install handle into spool.
7.
surfaces and contamination.
Visually inspect cartridge valve for damaged sealing
F. Place ball and dowel pin in backlap switch man-
ifold port (Fig. 65). Install new O--ring onto backlap
switch. Thread backlap switch into port and torque
A. Contamination may cause valves to stick or hang
up.Contaminationcanbecomelodgedinsmallvalve
orifices or seal areas causing valve malfunction.
15
ft--lb (20 N--m).
B. If valve sealing surfaces appear pitted or dam-
aged, the hydraulic system may be overheating or
there may be water in the system.
10.Reinstall
cartridge valve into manifold:
A. Lubricate new seal kit components with clean hy-
draulic oil and install on valve. The O--rings, sealing
ringsandbackupringsmustbearrangedproperlyon
the cartridge valve for proper operation and sealing.
CAUTION
IMPORTANT: Use care when installing cartridge
valves. Slight bending or distortion of the stem
tube can cause binding and malfunction. Make
sure that deep well socket fully engages the
valve base.
Use eye protection such as goggles when using
compressed air for cartridge valve cleaning.
CAUTION
B. Lubricate threads of cartridge valve with clean
hydraulic oil. Thread cartridge valve carefully into
correct manifold port. The valve should go in easily
without binding.
Abrupt movement of internal spools can cause
stored fluid to be released suddenly.
C. Torque cartridge valve using a deep well socket
to values identified in Figures 62 and 65.
8.
Clean cartridge valve by submerging valve in clean
mineral spirits to flush out contamination. Particles as
fine as talcum powder can affect the operation of high
pressure hydraulic valves. If cartridge design allows,
use a wood or plastic probe to push the internal spool in
and out 20 to 30 times to flush out contamination. Be ex-
tremely careful not to damage cartridge. Use com-
pressed air for cleaning.
2
20 ft--lb
1
(27 N--m)
3
41
ft--lb
(55 N--m)
1
4
9.
ifold, install spool (Fig. 64):
If mow/backlap spool was removed from mow man-
15
(20 N--m)
ft--lb
UP
5
A. Install O--rings and back--up ring to upper
grooves on spool. Apply a light coating of grease to
O--rings.
6 7
8
9
10 11
B. Carefully push spool down into mow manifold
port until lower O--ring and back--up ring groove is
exposed on bottom of manifold. Install lower O--ring
and back--up ring to spool. Apply a light coating of
grease to O--ring.
12
13
1
3
14
6
14
7
198
(
in--lb
22 N--m)
165 in--lb
(18.6 N--m)
8
C. Carefully raise mow/backlap spool until upper re-
taining ring groove on spool is exposed on top of
manifold. Install upper retaining ring.
9
Figure 65
1.
2.
3.
4.
5.
6.
7.
Seal kit
8.
9.
O--ring
Logic cartridge
Backlap switch
10. Orifice (0.055)
11. O--ring
D. Push mow/backlap spool down and install lower
retaining ring to spool.
Mow control manifold
O--ring
Plug (zero leak #8)
Ball
Dowel pin
12. Plug (SAE #4)
13. Plug (zero leak #6)
14. O--ring
Hydraulic System
Page 4 -- 78 Rev. B
Reelmaster 5010 Series
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work