Removal (Fig. 52)
Park themachine onalevelsurface, engage parking
Installation (Fig. 52)
1.
1. Applyantiseizelubricanttotractionpumpinputshaft.
brake, lower cutting units and stop engine. Remove key
from the ignition switch.
2.
put shaft.
Positiondriveshaftassemblytoengineandpumpin-
2.
that secure drive shaft guard hoop to machine frame.
Remove guard.
Remove two (2) flange head screws and flange nuts
3.
(6)
42
Secure drive shaft flange to engine flywheel with six
cap screws (item 7). Torque cap screws from 34 to
ft--lb (46 to 56 N--m).
3.
(item9)thatsecuredriveshaftyoketopistonpumpinput
shaft.
Remove two (2) cap screws (item 5) and flange nuts
4.
(2)
Secure drive shaft yoke to pump input shaft with two
cap screws (item 5) and flange nuts (item 9).
5.
and secure with two (2) flange head screws and flange
nuts.
Position drive shaft guard hoop to machine frame
4.
shaft flange to engine flywheel.
Remove six (6) cap screws (item 7) that secure drive
5.
Remove drive shaft assembly from machine.
Drive Shaft Cross and Bearing Service (Fig. 53)
Remove snap rings that secure bearings in yokes.
6.
Lubricate grease fittings on drive shaft.
1.
4
3
IMPORTANT: Yokes must be supported when re-
moving and installing bearings to prevent damage.
2
1
2.
Use a press to remove cross and bearings from
yokes. Thoroughly clean drive shaft yokes.
3.
To install new cross and bearings:
A. Apply a coating of grease to bearing bores in end
yoke and shaft yoke.
B. Press one bearing partially into yoke.
C. Insert cross into yoke and bearing.
3
D. Hold cross in alignment and press bearing inuntil
it hits the yoke.
Figure 53
1.
2.
End yoke
Cross and bearing kit
3.
4.
Snap ring (4 used)
Shaft yoke
E. Install snap ring into yoke groove to secure
installed bearing.
F. Place second bearing into yoke bore and onto
cross shaft. Press bearing into yoke and secure with
snap ring.
G. Repeat procedure for other yoke.
H. Greasecrossuntilgreasecomesoutofallfour(4)
cups.
4.
Make sure that assembled joint moves without bind-
ing. Slight binding can usually be eliminated by lightly
rapping the yoke lugs with a soft faced hammer. If bind-
ing continues, disassemble joint to identify source of
binding.
Reelmaster 5010 Series
Page 4 -- 61
Hydraulic System
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work