7.
Remove brake drum.
7. Install the lock nut (item 17) onto the wheel motor
shaft and torque from 250 to 350 ft--lb (339 to 447
N--m).
IMPORTANT: DO NOT hit wheel hub, puller or wheel
motor with a hammer during wheel hub removal or
installation. Hammering may cause damage to the
wheel motor.
8. Install brake drum.
9.
Position brake cable end to brake actuator lever. Se-
8.
loose. Use appropriate puller to loosen wheel hub from
wheel motor shaft.
Make sure that lock nut on wheel motor shaft is
curecabletoactuatorleverwithclevispinandcotterpin.
10.Install
front wheel assembly (see Wheel Installation
in this section).
9.
Locate and retrieve woodruff key.
Remove lock nut and wheel hub from motor shaft.
11.
Check and adjust brakes.
12.Lower
machine to ground.
NOTE: If desired, the complete brake assembly can be
removed from the machine for disassembly (see step
12).
13.Torque
to 90 ft--lb (95 to 122 N--m). Torque lock nut (item 17)
that secures wheel hub from 250 to 350 ft--lb (339 to
lug nuts evenly in a crossing pattern from 70
10.Remove
shoes.
upper and lower shoe springs from brake
447
N--m).
11.
springs. Remove brake shoes and hold down pins from
backing plate.
Remove shoe hold down cups and hold down
CAUTION
12.If
loosening and removing four (4) cap screws and lock
nuts.
necessary, remove backing plate from machine by
After servicing the brakes, always check the
brakes in a wide open, level area that is free of
other persons and obstructions.
Installation (Fig. 5)
1.
Remove rust and debris from all parts with a wire
14
brush prior to installation. Clean all parts. Inspect brake
shoe contact surfaces of the brake drum for excessive
wear. Replace any worn or damaged parts.
13
12
11
10
2.
backing plate to brake bracket with four (4) cap screws
and lock nuts.
If backing plate was removed from machine, secure
5
14
9
2
3.
purpose grease.
Lightly lubricate brake shoe pivot points with general
3
1
4
4.
Position one brake shoe to the backing plate. Install
brake hold down pin and secure with hold down spring
and cup. Repeat for second brake shoe.
5
6
7
8
5.
Install upper and lower shoe springs to brake shoes.
Make sure that brake shoes are properly positioned to
pivot and actuator points.
Figure 6
8.
9.
1.
2.
3.
4.
5.
6.
7.
Backing plate
Rivet (4 used)
Clevis pin
Retaining ring
Brake shoe
Lower shoe spring
Hold down spring
Hold down cup
Upper shoe spring
10. Brake actuator
11. Actuator lever
12. Back--up plate
13. Boot
IMPORTANT: Before wheel hub is installed, thor-
oughly clean tapers of wheel hub and wheel motor
shaft. Make sure that tapers are free of grease, oil
and dirt. Do not use antiseize lubricant when instal-
ling wheel hub.
14. Hold down pin
6.
wheel hub onto the wheel motor shaft.
Mount key in the wheel motor shaft, then install the
Reelmaster 5010 Series
Page 6 -- 9
Chassis
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work