Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual

Up Limit Switch
The up limit switch is a normally open proximity switch
that closes  when the cutting  units are in  the lowered
position. A bracket on the front, right lift arm acts as the
sensing plate for the up limit switch (Fig. 37). The switch
on machines with a serial number below 310000000 is
different than the switch on machines with serial num-
bers above  310000000 but the  switch function is  the
same.
5.  If the up limit switch tests correctly and a circuit prob-
lem still exists, check  wire harness (see Wiring Sche-
matic and  Circuit Drawings  in Chapter  9 --  Electrical
Diagrams).
6.
Make sure that wire harness electrical connector is
connected to the up limit switch after testing.
Testing
1
1.
Before testing the up limit switch, the switch and its
4
circuit wiring should be tested as an ECM input with the
Diagnostic Display (see Diagnostic Display in the Trou-
bleshooting section  of this chapter).  If the Diagnostic
Display verifies that the up limit switch and circuit wiring
arefunctioningcorrectly,nofurtherswitchtestingisnec-
essary. If the Diagnostic Display determines that the up
limitswitchandcircuitwiringarenotfunctioningcorrect-
ly, proceed with testing procedure.
2
3
5
2.
On machines with serial numbers below 310000000
(Fig. 37), test up limit switch as follows:
A.  Make sure ignition switch is in the OFF position.
Disconnect  the wire  harness  electrical connector
from the switch. Check thecontinuity ofthe switch by
connecting a multimeter (ohms  setting) across the
switch connector terminals.
Figure 37
1.
2.
3.
Lift arm
Up limit switch
Sensing plate
4.
5.
Lock nut (2 used)
Switch bracket
3
2
B.  There should be continuity (closed) between the
switch terminals when the cutting units are lowered.
Raisethecuttingunitsandcheckthecontinuityofthe
switch. There should not be  continuity (open) be-
tweentheswitch  terminalswhenthecutting  unitsare
raised.
SERIAL NUMBER
ABOVE 310000000
1
2
3
3.
(Fig. 38), test up limit switch as follows:
On machines with serial numbers above 310000000
LED location
A.  Turn ignition switch  to the ON  position (do not
start engine) and check LED on cable end of up limit
switch.
4
B.  LEDshouldbeilluminatedwhenthecuttingunits
are lowered. LED should not be illuminated when
the cutting units are raised.
FRONT
NOTE:  When installing the up limit switch on machines
with  serial numbers  below 310000000,  place  switch
plate tab into switch mounting hole that is closest to tar-
get end of switch.
Figure 38
1.
2.
Up limit switch
Lock washer
3.
4.
Jam nut
Lift arm
4.
If  up limit  switch  is faulty,  replace  switch. Adjust
switch after installation (see Up Limit Switch in the Ad-
justments section of this chapter).
Reelmaster 5010 Series
Page 5 -- 31   Rev. B
Electrical System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 292 pages
Document TypeCatalog, Service Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual SKU UPC Model
Alfredo Gonzalez on Jun 06, 2014.

i hope is going to work


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website