6.
Anytime the machine is parked (short or long term),
7. Do not park on slopes unless wheels are chocked or
blocked.
the cutting units should be lowered to the ground. This
relieves pressure from the hydraulic lift circuit and elimi-
nates the risk of the cutting units unexpectedly lowering
to the ground.
Maintenance and Service
1.
ting units, stop engine, apply parking brake and remove
key from the ignition switch.
Before servicing or making adjustments, lower cut-
11.Shut engine off before checking or adding oil to the
crankcase.
12.Disconnect
battery before servicing the machine.
2.
keeping all nuts, bolts and screws tight.
Make sure machine is in safe operating condition by
Disconnect negative battery cable first and positive
cable last. If battery voltage is required for troubleshoot-
ing or test procedures, temporarily connect the battery.
Reconnect positive battery cable first and negative
cable last.
3.
wherethereisanopenflame, suchasnearawaterheat-
Never store the machine or fuel container inside
er or furnace.
13.Battery
Avoid contact with skin, eyes and clothing. Protect your
face, eyes and clothing when working with a battery.
acid is poisonous and can cause burns.
4.
all hydraulic hoses and lines are in good condition be-
fore applying pressure to the hydraulic system.
Make sure all hydraulic line connectorsare tight, and
14.Battery
and flames away from the battery.
gases can explode. Keep cigarettes, sparks
5.
Keepbodyandhandsawayfrom pinholeleaksinhy-
draulic lines that eject high pressure hydraulic fluid. Use
cardboard or paper to find hydraulic leaks. Hydraulic
fluid escaping under pressure can penetrate skin and
cause injury. Fluid accidentally injected into the skin
must be surgically removed within a few hours by a doc-
tor familiar with this form of injury or gangrene may re-
sult.
15.When changing attachments, tires or performing
other service, use correct blocks, hoists and jacks.
Make sure machine is parked on a solid level floor such
as a concrete floor. Prior to raising the machine,remove
any attachments that may interfere with the safe and
proper raising of the machine. Always chock or block
wheels. Use jack stands or appropriate load holding de-
vices to support the raised machine. If the machine is
not properly supported, the machine may move or fall,
which may result inpersonal injury(see JackingInstruc-
tions in this section).
6.
Before disconnecting or performing any work on the
hydraulic system, all pressure in the system must be re-
lieved by using all of the hydraulic controls (see Reliev-
ing Hydraulic Pressure in the General Information
section of Chapter 4 -- Hydraulic System).
16.If
sired, contact an Authorized Toro Distributor.
major repairs are ever needed or assistance is de-
7.
units. Wear gloves and use caution when servicing
them.
Use care when checking or servicing the cutting
17.If welding on the machine is necessary, disconnect
the negative battery cable to prevent electrical system
damage.
8.
free of excessive grease, grass, leaves and dirt. Clean
protective screen on machine frequently.
To reduce potential fire hazard, keep engine area
18.At the time of manufacture, the machine conformed
to the safety standards for riding mowers. To assure op-
timum performanceand continuedsafety certificationof
the machine, use genuine Toro replacement parts and
accessories. Replacement partsand accessoriesmade
by other manufacturers may result in non-conformance
with the safety standards, and the warranty may be
voided.
9.
If engine must be running to perform maintenanceor
to make an adjustment, keep hands, feet, clothing and
other parts of the body away from the cutting units and
other moving parts. Keep bystanders away.
10.Do
setting. Toassuresafety andaccuracy,checkmaximum
engine speed with a tachometer.
not overspeed the engine by changing governor
Reelmaster 5010 Series
Page 1 -- 3
Safety
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work